Walau....this thread getting so hot so fast
Sorry quite bz this few days
Will come back follow AMD clan after monday or tuesday
Reason ......

And i wish good luck for those join Mini-OC Challenge

This post has been edited by digswell: Oct 17 2008, 06:36 PM

Opss...seems like a lot of ppl joining Mini OC tomorrow.
Good luck to you all.

-pWs-

OH CRAP!!!! I'm late to know that there's a clan for AMD Mini OC with a female host......

Too bad my Phenom codename Agena broke down..... can't join you ppl........

anyway, work hard everyone........

This post has been edited by amane_kaoru: Oct 17 2008, 07:07 PM

Sorry Bro ! keep u waiting

Increase A NB/SB Link Clock - (put 120-140) it's fine for me lo.

If increase the northbrige and southbridge clock to 140, what's the temperature of your northbridge and south bridge?

Not above 50C actually. with help from 40cm fan

oh i see..... when i start my 1st oc on my proc, i was using Opteron codename agena with stock fan. from 1.8Ghz raised to 2.6Ghz. the temperature raised from 40 degree to 85 degree. i was shock till dead.

i still learning on OC the RAM. you know about the timing of the RAM? mind to explain some to me?

i tot the quad core opteron come with barcelona code name??

it's my mistake, my opteron is single core. it's code name venus and it's my phenom which broke down. 2 pins broken.

fall?

nope. i apply, remove, apply, remove, apply, remove, apply, remove, apply, remove, apply, remove, apply, remove, apply, remove, apply, remove, apply, remove, apply, remove, apply, remove, apply, remove, apply, remove, apply, remove, apply, remove, apply, remove, apply, remove, apply, remove, apply, remove, apply, remove, apply, remove, apply, remove, apply, remove, apply, remove, apply, remove, apply, remove, apply, remove, apply, remove, apply, remove, apply, remove, apply, remove, apply, remove. Then suddenly misplace it then put on heatsink and lock the lever.

This is how it ends within few days.......................

huhu... same story with my pentium 4. luckily the pin only bent and can be straighten using long nose player. but 1 pin become a bit loose.
after that i will always remember to look for the right pin when inserted the processor.

a soldier die even b4 go into battle field...

that's an expensive experience to gain for sure...

i feel for u mate...

@ bro digswell,

tengah sibuk upgrade ke?

This post has been edited by ah_khoo: Oct 17 2008, 08:28 PM

when i send back to C-Zone in lowyat plaza, that guy say if pin bend can go claim warranty but you can't claim it once broken.
So, he advice me, if bend..... dont try to straighten it. go claim warranty straight away cause try straighten it yourself might broke it.

Meanwhile, i'm trying to ask pro to see either it can be soldered back or not. >.<

newbie joining the clan


This post has been edited by arayz: Oct 17 2008, 09:53 PM


Attached thumbnail(s)

I guess even if you manage to get the pins soldered, the pins will not as solid as the original one.

-pWs-

i dun think there's anyway to solder a broken pin bro... even if can how on earth d soldered part can fit into d small hole of d cpu socket...

I m not sure about processor.
But I did have my motherboard soldered by my friend.

-pWs-

d pins of amd chips are so fine until it's impossible to solder even w/ steadiest hands.

d last time i soldered a board, i killed it...

i'm improvin as i just managed to solder d broken wire of my soon to be sold casing's speaker yesterday... it was done usin those el cheapo solderin gun...

@ imsmiko,

pls upload this useful tool for k10, it's called k10 calculator:

 K10Calc.zip ( 164.85k ) Number of downloads: 2


* credit to XS member Nedjo, source HERE...

This post has been edited by ah_khoo: Oct 17 2008, 10:30 PM

What to set? 270x10 ddr400 can not boot

I'm using Ocz 6400 reaper .check my siggy. Not a super overclocking ram




Attached thumbnail(s)