yes u can.

yeah.. something like those vcd in pasar malam...

errr you wanna defect? haha then what shall i tell Jon or Steven la? tell them that one of Mud Legion's has gone into Marauderz? haha. hehe bahaya tu bro haha.

u can ask this guy down here

hey zzub... nice thundercats boxer.... hehehe..

OT...? nah.. don't think so....

not to say totally no problem, just lesser chances.


PM8, compared with PM7
smaller LPR,
eye pipe included,
changes in bolt top can design,
ultralight frame included,
14" barrel included,
Eye ribbon Smaller,
HyperReg3,

PM7 compared with PM6,
different LPR outer design,
Different electronic-board design,
different eye cover,
Slimmer body.

that's about all that i could think of now..

anyway..the new alien is out bad .. 2 piece barrel and the looks also i hv to say, really tempting almost like ego

oh by the way... DM9 is around the corner....

http://www.dyeprecision.com/Media/Videos/DM9_TeaserA.mov

eh..? thot pm8 uses wires instead of ribbon for its eyes.. or did i read it wrong..? (i don't own a pm8 lah, can't tell for sure)
weight is subjective, some 08 markers are way heavier than even a pm5...
so, if we put ultralite frame on say a pm7, would it be on par with pm8..? ok, the eye pipe cannot kira la as only 08 version got them.... i mean the shooting lah, with all the advancement, is there any improvement on accuracy.. air efficiency of course la since it's a diff bolt...

already out like few month already lah.. ain't got the dough, so just drool over it for now lah...
yeah.. looks something like an ego, but then most marker would look the same if u shave off the unuse metal..
well, the indy is fitted with special hyperdrive board (u can't get it from hyperdrive but only at aliens) & green laser eyes.. u even get 2 trigger frames - 45 & 87 deg handles, it's ur choice..

yeah... i only read about the release about a month back

wats the diff 45 and 87 deg handles?

already check about it.. tak perasan grip dia diff... ...

This post has been edited by zzub: Sep 5 2008, 05:37 PM

nope it's still ribbon.

PM7 vs PM8, i'd go for the PM8s, the new LPR with shim stacks gives a better consistency as over time, Spings will lose their tensions.
Bolt wise, slight difference. not noticeble if one is not careful.

as usual, accuracy rely more on the ball to barrel fit than the built of the marker itself.


anyone drooling on the DM9 yet?

aiya.. sudah pening pasal marker
guna mechanical sudahhhh..
ktehh ktehhh ktehhhh... kelepek!

12" still kicks arse...

7" kicks other things.

order the premium package & u'd get both handles plus 2 additional 7" back & few fronts.. one of them is a cf barrel... just like buying 2 markers...

well, i only read & heard abt the wires, don't know for sure since haven't got any chance to really explore it... no one dare to give me for that yet...
yeah... efficiency & consistancy should be the later model advantage.. accuracy is kinda subjective...
dm9, yet to read abt them... donno lah, my interest is more to proto than dye... not that dye it has any flaws over proto, except when there's only 1kpsi or less air left... but still dm is a good marker... tak rugi ambik, just personal preference i guess..



dont care lah.. u still need foot to kick.. else it might just be a whack or a slap...

well.... its stated some marker using only 100-180psi to operate (droid, Ego etc).. and some marker like VS2, ion etc need around 200-300psi... can use low pressure tank ke on VS2 etc?....

can.. coz lp tank's output is around 450psi while hp tank is abt 850psi..
most would choose to use hp to ensure supplied pressure is sufficient, esp during rapid fire...

if i'm not mistaken it's all up to what your LPR or Regulator can accept. if it's a HP reg, using a LP tank on it should be fine... but if it's a LP reg, then a HP reg might sent it to hell...

i might be wrong in this since most of the marker that i service runs on HP tanks without hiccups.

which reg are u referring to..? tank reg or marker reg.?
IMO, whichever it is, reg is to regulate the pressure, in other word it limits output to specific pressure, no matter what the input is.. unless the input is smaller than the intended output then that would be a prob lah...

tank capacity = 3000/4500 -> tank reg output = 450/850 -> lpr = 75 ~ 250

err.. anybody know the output of marker inline reg ah...?

*the more knowledgable please correct if i'm wrong here

wa onli tau tembak... pasal reg n pressure wa langsung no clue...