From the picture above, the wireless "rate" show 54mbps and it seem to be ok..
But in my case, the rate always drop to 1,2, 5.5mbps. Till now, it never reach 54 anymore.
I'm already set the transfer rate to 54mbps but the line still slow.

Tq.

It seems u don't understand how wireless work if u far away of course the wireless signal will drop

If u want to get 54Mbps all the time sit next to ur AP or force to use G mode and set the transmission mode to 54 Mbps but if u do this the router might not work with ur PC

Please note:Typical Wireless Range will be dependent on the following:

1. Transmit Power of your Access Point or Wi Fi Router
2. Outdoor Obstructions (trees, lakes, buildings, RV's, hills, etc.)
3. Type of building material (metal, aluminum, wood, sheetrock)
4. Mounting position of antenna
5. dbi Gain of the outdoor antenna
6. Length of coax cable connected to the Wi Fi antenna
7. Client device receive sensitivity, and transmit power

is there special dd-wrt for dir-825 ??

hmm i would like to know any other router recommandation that can install ddwrt and it has lots of ram? cuz my current wrt54g v5 really lag like hell when using torrent...cant access the webgui to config shits...

This post has been edited by intothefantasy: May 8 2010, 03:53 AM

thanks..

actually i read this before, but i just do half of the steps.. missed few last steps. no wonder not working..

Linksys WRT54GL

@MX510, for flashing WRT54g v3.1 ori to dd-wrt, do i need to use the mini 1 to flash it 1st?

DONE, btw another problem exist... ...why the power led blinking..i can using it on9, just power led blinking..

Solved, i restart the router, ..mayb i change setting will affect the power led too....

This post has been edited by experty2010: May 11 2010, 06:04 PM

need to ask dd-wrt gurus here

i have 2 router dir-600 (standard v24 preSP2 dd-wrt) and wrt54g2 (micro dd-wrt). if i want to setup repeater or wds which one should be use as primary and secondary. by the way can i setup wds using this router ?

This post has been edited by kelembai: May 11 2010, 02:26 PM

Go to mini version then go to standard

Refer here

http://www.dd-wrt.com/wiki/index.php/Linksys


Not sure for Standard version the WDS is working or not

Tutorial available here

http://www.wi-fiplanet.com/tutorials/artic...ss-Repeater.htm

Done..thanks.

http://www.wi-fiplanet.com/tutorials/artic...ss-Repeater.htm

[/quote]

okey thank , by the way repeater available on standard and micro ?

This post has been edited by kelembai: May 11 2010, 11:16 PM

hi, using Linksys WRT54GS, flashed to DD-WRT around 2 months back...i notice everything i click on the "disconnect" button at the WAN status page, my wireless connection will be disconnected, and wait around 20 seconds like that then it will reconnect back....it seems like a router restart to me..

is this happening to anyone as well? or is this the default behavior of the firmware?

hmm....why does the latest version of DD-WRT don't have connect on demand in WRT54GL v1.1?, it makes constant dc until so badly that i have to revert to tomato, any ideas how to solve it?

any1 flashed their dir 600 with ddwrt?

im currently facing occasional lag spike over WAN (request time out)..
ping to modem is smooth tho as of currently im using wifi.

Sure got lah bro where did u see no dod ?

Screenshot pls

My IPhone connecting to DIR600 + DDWRT > Billion Modem
damn slow.... Billion modem using router mode, while DIR600 act as a AP only.

When I go to my frd house, using all in one modem/router/w.less
i can get instantly speed.

Current setting in my iphone, 192.168.1.1XX, DNS : TM DNS, DIR600 : TM DNS other default.

MX510, this is the pic =.=", any ideas?


Attached thumbnail(s)

Tick on the Force Reconnect Button :-)

bro,,,,this software support WAG54G2 mah?

force reconnect button is disconnect and reconnect back your PPPoE status?
after i ticked, do i need to put time or leave it as default 00:00?

i want my connection to be 24/7 up and not disconnect and reconnect at certain period, is that force reconnect are solution to me?

This post has been edited by warlove3: May 17 2010, 10:06 PM