Hahaha cool bro :-) DD-WRT FTW :-)

so i bought d-link dir600

its firmware is Bx not B1 or B2

fml

so the box says its B2 w00t

gonna flash right nao

meh ver 2.02 not supported yet

This post has been edited by old_calculator: Apr 28 2010, 08:59 PM

http://dd-wrt.com/site/support/router-detection

Try this link

I think most of the dir-600 sold in malaysia are HW-VerB , if the dir-600 is HW-verB then it support dd-wrt , u can check the box of dir-600 , got written there

You may also try to search through it's router database:

http://dd-wrt.com/site/support/router-database

Just enter DIR, choose the correct model & revision.

For DIR-600, B1 & B2 are supported.

Also noticed that DIR-615 & DIR-825 are support now.

This post has been edited by zhuan97: Apr 29 2010, 10:55 AM

Thanks will check that

EDIT

Finally.. its flashed with dd-wrt

This post has been edited by old_calculator: Apr 29 2010, 04:44 PM

modem(192.168.1.1) ----> ddwrt(192.168.0.1) ----> pc

how can i access my modem webgui interface thru ddwrt? I tried 192.168.1.1 but can't access to the modem..

http://www.dd-wrt.com/wiki/index.php/Acces...m_Configuration

From the picture above, the wireless "rate" show 54mbps and it seem to be ok..
But in my case, the rate always drop to 1,2, 5.5mbps. Till now, it never reach 54 anymore.
I'm already set the transfer rate to 54mbps but the line still slow.

Tq.

It seems u don't understand how wireless work if u far away of course the wireless signal will drop

If u want to get 54Mbps all the time sit next to ur AP or force to use G mode and set the transmission mode to 54 Mbps but if u do this the router might not work with ur PC

Please note:Typical Wireless Range will be dependent on the following:

1. Transmit Power of your Access Point or Wi Fi Router
2. Outdoor Obstructions (trees, lakes, buildings, RV's, hills, etc.)
3. Type of building material (metal, aluminum, wood, sheetrock)
4. Mounting position of antenna
5. dbi Gain of the outdoor antenna
6. Length of coax cable connected to the Wi Fi antenna
7. Client device receive sensitivity, and transmit power

is there special dd-wrt for dir-825 ??

hmm i would like to know any other router recommandation that can install ddwrt and it has lots of ram? cuz my current wrt54g v5 really lag like hell when using torrent...cant access the webgui to config shits...

This post has been edited by intothefantasy: May 8 2010, 03:53 AM

thanks..

actually i read this before, but i just do half of the steps.. missed few last steps. no wonder not working..

Linksys WRT54GL

@MX510, for flashing WRT54g v3.1 ori to dd-wrt, do i need to use the mini 1 to flash it 1st?

DONE, btw another problem exist... ...why the power led blinking..i can using it on9, just power led blinking..

Solved, i restart the router, ..mayb i change setting will affect the power led too....

This post has been edited by experty2010: May 11 2010, 06:04 PM

need to ask dd-wrt gurus here

i have 2 router dir-600 (standard v24 preSP2 dd-wrt) and wrt54g2 (micro dd-wrt). if i want to setup repeater or wds which one should be use as primary and secondary. by the way can i setup wds using this router ?

This post has been edited by kelembai: May 11 2010, 02:26 PM

Go to mini version then go to standard

Refer here

http://www.dd-wrt.com/wiki/index.php/Linksys


Not sure for Standard version the WDS is working or not

Tutorial available here

http://www.wi-fiplanet.com/tutorials/artic...ss-Repeater.htm

Done..thanks.

http://www.wi-fiplanet.com/tutorials/artic...ss-Repeater.htm

[/quote]

okey thank , by the way repeater available on standard and micro ?

This post has been edited by kelembai: May 11 2010, 11:16 PM

hi, using Linksys WRT54GS, flashed to DD-WRT around 2 months back...i notice everything i click on the "disconnect" button at the WAN status page, my wireless connection will be disconnected, and wait around 20 seconds like that then it will reconnect back....it seems like a router restart to me..

is this happening to anyone as well? or is this the default behavior of the firmware?