i think u need to stop if u want to use as 24/7

24 hours.. open non stop.. but what is ur current result now??

Q proc u have.. how both mobo n proc price ha??.. pm me..

wah.. teaching him sub timing..

no need for now .. just loosen 105ns to 195ns

@Mr_Habuk

before this u asking differences when using other trfc rite??
i show u this
every sec that u reduce need in using the high vdimm..every sub timing depending on each other..

example, when u use 195ns(previous said by me)
it yield:

the bandwidth:
[attachmentid=503300]
the SPI 1m : 28.532s
[attachmentid=503298]

when u use 75ns( required more vdimm, depend on what situation)
it yield:

the bandwidth:
[attachmentid=503299]
the SPI 1m : 28.391s
[attachmentid=503297]
usually when oc u need to loose all the timing to make sure the ram have not much burden on it. the difference in time (FYI, i run a SPI again and again to find the best time when changing the trfc) just a little but in other word it represent the vdimm. but in my case i dun need any vdimm changes. in oc tries, it is better to loosen all timing to make sure it can use the low vdimm u feed to them..

besides that, the bandwidth have a bit differences.. so ask urself what to use and when to use..

the most important thing the MAL, trfc and 5 timing that u need to care in beginning of not an extreme oc, after u got the skill how to tweak it even better, u can play the other subtiming..

oc divide by two categories ( it's applied to me )
- extreme (trial) -other sub timing need to care for better result
- daily usage.. -only what i edi say at above..

just my 2 cent.. correct me if i'm wrong

yap, we wont notice any different, the software tell u the different, in real life it doesnt matter..
if u success to oc 25% from stock, it alredi good achievement..

tat why u need to lend for me .. then i can test kaw2..haha

too much how much??

can i know what mobo u use??
still in the range of acceptance.. no burn..

This post has been edited by xixo_12: Jun 20 2008, 05:45 PM

i recommend u to stop at 1.5v.. then change the cooling..u want to do WR ha?? haha

shh.. but still got skill in ocing

@blue16
try it urself


This post has been edited by xixo_12: Jun 21 2008, 11:47 AM

604 bios TA690G
new bios release

This post has been edited by xixo_12: Jun 22 2008, 11:28 AM

bro ah_khoo..
how the vcore max n vdim ax78 ha??

no la.. just asking..looking for vcore 2.0V..haha

if can use that mobo

looking for 1.8v shud be ok

lol...

how bout DFI DK or UT??
max vcore vdimm??

ah_khoo, can u disable 3 core, and try to push alone.. want to see la..
before this 3800 f3 able to run 3.2ghz with 1.23V.. play with single core doesnt have pain alot.. then if want run heavy prog, enable it back.. but have to lower to 3.1 back

This post has been edited by xixo_12: Jun 26 2008, 02:30 PM

org tue konon..gud luck in 2.613ghz (push by clockgen)

after test with alot of bios.. then finally i can score it..

wrong.. not the 1M, it's 32M, try a few bios to pass 260 x12, finally i found the bios that help me to achieve it, HT link so high doesnt give any effect, i use 10th anni with 1.95v in bios onli..

u must do try n error, different chipset of ram give different score.. maybe u must read a lot in ram tweaking

getting fed up, can't find the best mobo nowadays..prefer matx..any suggestion?? dun want the AMI bios

the keyword Matx