Halo brother brother sekalian, If I were to flash my bios (TA690G) which version is most stable and best at the moment ? Went to lejabeach but not sure which to take.

Hi guys,

I just setup the F3 with the DFI NF Ultra M2 yesterday with D9gmh 512x2. Can I know is the stock bios good to use to oc it ? I set the vcore to "default" and 1.8V for the ram, DDR533, 250 x 10, FSB ratio 4, no prob to boot up to 2.5GHz, 1000 HT and 625MHz for ram at 4-4-4-12-1T.

But, if i go above 250fsb, it can't boot up even though i change the fsb ratio to x3. Need more vcore ? May I know whats the default value ? Should i set to 1.200V or higher ?

Bro -pws- and CV6149: same board as u guys, what to do next to get 3.1ghz ? Using TT V1, temp in Everest is 33C on each core.

CV6149: this is the burnt mobo lo, hehehe, manage to replace the diode. Testing it out b4 try out on the abit NF-M2 nView.

Please help to guide noob guys.

Will upload SS tonite, its at home now. idling.

welcome another DFI bro
Wah...u so good ah? Can repair mobo huh?

Mind to share which Diode u replaced? near the 24-pin power connector?

Anyone ?

Oh, nolar, just solder take out the burnt diode and then replace it with a straight wire lo. If burnt again, the whole mobo will be roasted lo coz the diode is no longer there to protect it. hehehe.

Its near the IEEE 1394 pins there. Since it no longer valid for warranty, just try to repair it and test lo. at 1st can't work wan, but after resetting the bios, take out the battery, then it come alive again. hehe

Now, its running in open air in my room.

Just trying to oc the F3 now, kinda easy to oc to 250 x 10, but to go higher, i think mayb need new bios or higher v-core, not sure, so need to ask for opinions.

My rams won't b bottleneck since it can do 1000MHz 5-5-5-15-2T with 2.2V without heatsink or fan. but must aircond room. hehe.

my same DFI model will go >3.2G only when use x8.5 or 9.
X10 stuck at 3GHZ

Maybe u can try out lower multi.

Oh, ok, cool, i'll try to lower the multi tonite.

Thanks for the advice. Will give it a try tonite.

By the way, may I know which is the multi ? I mean in the Genie bios section, which option to tweak ? 35.406s for the 1m super pi is it normal ?

Also, to join in the clan for AMD OC, what are the SS required ? I remember u guys need the Super Pi 32M, what else ?

Yoo...Welcome
What multi you meant bro??

You can play w ram timing in Genie

-pWs-

not much 2.25 onli orthos keont surpass 1 hour. fack... need better Switch A-Data DDR2800X Extreme Edition over, this my dads rigs onli.

U pump in 2.25 on value ram ? Wow, not afraid of getting burnt ? Any active cooling ? As for value ram, do not exceed 2.1 later fry egg =D

Owh, yeah anyone ?

"Halo brother brother sekalian, If I were to flash my bios (TA690G) which version is most stable and best at the moment ? Went to lejabeach but not sure which to take."

@mizivincible
Wait for those Biostar user.
I think they already discussed it before.

-pWs-

Wokek, haha sorry very annoying pulak. Wait for bro DB la then. Dont know why when reaching 3.0ghz at 1.44v sometimes orthos pass over 2-3hours and sometimes not even 5 minutes.

As I was planning to go at 3.0ghz on 24/7.

Of course with lower vcore is better. And to think it back last time when I just got my brisby few days before the F3 bulk was on. Haihz .... If I late few days surely windsy is accompanying me now. But nvm since brisby also good so no regret =D

This post has been edited by mizivincible: Jan 7 2008, 05:32 PM

Actually the mid range performance ram same like XMS2, its wrap with heatsink relax...

Better w active cooling.

-pWs-

more burn in needed perhaps.

06/05 is d best so far, dats wat i've been told & usin rite now but dun quote me on this...

no problemo regarding the cd, sell one of ur tyre, then add rm10.. go to garage sell, u will got it..

too many question.. look for 605 punya bios.. faster2 to DL

This post has been edited by xixo_12: Jan 7 2008, 08:41 PM

http://forum.lowyat.net/index.php?showtopi...t=0&p=15023526&

kindly use 1.43 cpu-z

CPU-Z 1.43 has been released. Changes are as following :

Intel Skulltrail platform support (Core 2 Extreme QX9775 + 5400B MCH).
Intel X48 chipset detection.
AMD Athlon 64-LE 1600 and 1620 support.
Fix detection issues on unlocked Phenom (ES/BE).

This post has been edited by xixo_12: Jan 7 2008, 08:49 PM

http://www.xtremesystems.org/forums/showthread.php?t=169709

DFI fan updated.. new mobo n bechmark

Already got my G2... but will only do testing tomorrow afternoon. Tonite still testing some cheapo ProMOS, and not gonna sleep too late coz got class tomorrow.

Any Biostar TA770 user here?Wanna discuss about this board's setting.