I have encounter this problem almost whole week le.
1st, i go to BIOS setting there put CPU Multiplier = 10x , Cpu frequency = 300.
After that, i saved to CMOS and reboot, after that , got a message tell me to use another pofile to continue log on to windows.
But when i set Multiplier = 11X , Cpu frequency = 228 = 2508GHz it will run , can log on to windows with no problem.
Why ?? Anyone can help me ??

This post has been edited by 168257061: Aug 12 2007, 12:15 AM

u didn't even mention your computer spec how to help?

besides 11x228 is not the same as 10x300

dont expect any processor can run 3ghz so easily

This post has been edited by soulfly: Aug 12 2007, 11:41 AM

to TS, how we might help ya when there is no info bout ur current system.. zZZzz

list down abit laa

lolx, forgot
ok spec is shown below
AMD64 X2 4400+ 2.3GHz
Gigabyte GA-M57SLI-S4
Kingston 1024MB DDRII 667 RAM
Gigabyte 7300GT GPU
I-cute 450W PSU (chapalang maybe)
80GB Hiteachi DeskStar SATA HDD.

hmmm...i think first u have to pay attention to ur psu..icute is not a gud psu for OC, u should change to better one if u plan to OC ur proc

try increase to 2.9Ghz and see how..

Ok, even 240 frequency X 11 multiplier also cant proceed into windows oo....
About psu, those rm80-90 cap ayam psu cant oc or not good for oc??

if u not care bout burnin' to ur system, then can go ahead

even with non-oc system, cap ayam psu able to kab0omm

Nvm, bomb then buy 1 more.
oo, but after i pressed F1 continue to boot, logged on into windows, i open the cpu-z it is not showing mine setting.
My problem is --> I set it to total of 3.0Ghz(300x10) cpu speed, but after continue to boot, the cpuz just show me a total of 2.0Ghz of cpu speed only.

This post has been edited by 168257061: Aug 12 2007, 09:17 PM

i think somehow ur bios didnt save ur setting if like tat..double check it..

if the psu explode nvm...afraid it take all ur hardware together only..then tat time u mayb need more $$$ to replace all ur new hardware

since im not using amd anymore, im not quite sure wheter current am2 capable of doing 300x10 without hard-effort..
but IIRC, in s939 ages, u need to tweak the voltages, RAM, HTT, HTT multi etc correctly than only it will run at desired setup.. else, it will reboot at default speed only

i know the voltage setting,but how to put the suitable voltage for different frequency?
*Wait later mid night i will post those photos...

so.... how's ur rig...? Original Resipe or Extra Crispy...?

TS, i suggest you read and do some research before you even start to OC. You don't even have the slightest idea about overclocking. Don't expect people to spoon feed you.

I am guessing that you just bump the frequency without touching any other settings. If that fail, you should start increasing the vcore, step by step. Still cannot, then bring the HT down to 4X...so on and so forth.

As for the PSU If you still wanna OC....Change the PSU.

haiyo... u absolutely have no idea on ur problems.. try to find thread ga-m55sli issue and u will get the idea why ur mobo won`t oc properly.

Not every AMD processor can do 3ghz easily. I think that's your problem.

Second soulfly's opinion.
That is your problem. If you are using Windsor processor, it is hard for you to get 3GHz. Unless got one special case in LYN
AMD Windsor 3800 F2 go 3GHz

-pWs-

This post has been edited by -pWs-: Aug 24 2007, 05:26 PM

Is this your first attempt in OC? there's whole lot of story behind OC bro.. not just upping your CPU FREQ and thats all...