[attachmentid=10029709]
[attachmentid=10029710]
[attachmentid=10029711]
[attachmentid=10029712]

How to check whether stb got ip from tm server?
This network test at stb
[attachmentid=10029715]

ip from router dhcp 192.168.1.2

changed to 20mhz but the problem is still there,
the 2.4ghz signal strength was very weak and drops easily even not very far away.
Was so much different with RG4332's signal

Matcha=5ghz
Oolong=2.4ghz
We Are Happy Family=2.4ghz RG4332

[attachmentid=10029772]

[attachmentid=10029773]

is this suppose to be like this?? or is the radio parts for 2.4ghz is failing

[attachmentid=10029771]

The 2.4 Ghz is quite low power 100mW (20dBm). Maybe that's why.
The 5Ghz is 1W which is what I like.
Info from Aztech's IDA SG approval.
ftp://ftp.aztech.com/support/SINGAPORE/Ce...EGISTRATION.pdf

........
IT WORKS!!! Thanks a lot.  

after set the region to US, the signal become as strong as RG4332

[attachmentid=10030021]

[attachmentid=10030022]

am i need to set 5ghz to US also even if it is working fine?

RG4332 config is as attached, but i don't think it is readable?

[attachmentid=10030025]

i am asking the config file from aztech malaysia... and just get it... need to test it again...

because i reset, it become factory reset for another setting, not unifi...

here the file... need to unzipped first...

[attachmentid=10030739]

i hope i do the correct file attachment....

please give feedback if already test....

Now I use it as AP, it has very good hardware but the firmware is a joke. I bought YouHua WR1200JS as router, this model has dual-core 880MHz and 128MB RAM, with Padavan It can handle my 500mbps easily even with adblock on! Which is kindy surprise me due to I just paid about RM60 for this unit, the only cons for this is weak wifi, FG7008GR(AC) has good wifi but bad firmware, so I put them together makes them a strong team, strongly recommended. You may find some details on klseet website

I didn't enable it and it works, is it recommended to enable fullcone??
Actually this is the worst part, the firmware is end of support but the firmware is full of bugs, nothing near to "stable release"...
my router's configuration page sot jor, now cannot configure 5ghz at all, if click in, the page will hang there, and can't open the web ui again, even on other devices, sometimes it load, but drop down list for region setting will be empty... /.\

Finally unboxed my FG7008GR and did some quick tests. At least I know my first Aztech wasn't a fluke.

iPerf3 30-sec test from Ubuntu server to MacBook Pro Retina 15" which is 3x3. Link speed was 1300Mbps TX on the mbpr. Can't see the RX link speed but assume it's also 1300 Mbps.

[ ID] Interval          Transfer    Bitrate        Retr
[  5]  0.00-30.00  sec  1.53 GBytes  438 Mbits/sec    0            sender
[  5]  0.00-30.00  sec  1.53 GBytes  438 Mbits/sec                  receiver
[  7]  0.00-30.00  sec  1.53 GBytes  438 Mbits/sec    0            sender
[  7]  0.00-30.00  sec  1.53 GBytes  437 Mbits/sec                  receiver
[SUM]  0.00-30.00  sec  3.06 GBytes  876 Mbits/sec    0            sender
[SUM]  0.00-30.00  sec  3.05 GBytes  875 Mbits/sec                   receiver

What a lovely router, I mean AP. Have not tried it as a router yet.

More info here:
https://forum.lowyat.net/index.php?showtopic=4658454

so, after all these steps, i need to back flash to .003 again in order to use unifi pppoe?? then after that will this problem happen again?
and another issue i'm facing is that sometimes the 5ghz's channel will change by itself, and sometimes can't be detect, or connected but cannot access internet...

Read the pdf, I saw 802.11k, v, r are supported, means I can get two of it for AP and get roaming like what those mesh system do?

Manage to get this working both internet and iptv using aztech malaysia config (fw 007)

Speedtest 2.4g can get 58mbps on 72mbps link (Mi A1)
So good😁

So firmware .007 confirm compatible with unifi right?
It works only when using Aztech Malaysia config?
or which setting should i tick or chose?
previously using .007 but it can't connect unifi, but then using same settings in .003 and it works...so if i change back to .007, how to do the setting for unifi?

I've found a very interesting tips, when u try to make any changes for 5GHz WiFi, do it in basic tab, don't make any changes in advance tab, as it will cause the 5GHz to 20MHz bandwidth mode, the only change to make in advance tab is change country code, others please do it in basic tab