Yes I did. It stated error in flashing firmware.

Still facing Wifi reconnected and router restart problem with the beta firmware. And for me UNIFI stock firmware works the best although having the same problem.

should have AP setting and many more feature but mostly disable

HTML access at


http://192.168.0.1/webpages/pages/userrpm/

or http://your default gateway ip/webpages/pages/userrpm/

This post has been edited by RoxyGal: Jan 26 2018, 10:36 PM

AP mode is hidden but available...

Just a quick check. Did you fully reset the router after updating the firmware? As in pressing the tiny reset hole? There are few reports about settings aren't properly saved after updating from v40000 to v60000. A hard factory reset is needed instead of soft factory reset.

WDS Bridging is hidden as well. Geez....if all these functions are enabled, it would be a killer router.

Yea, hopefully TP-Link enables everything and releases an updated firmware soon...

The main problem = I don't think they will unlock the wifi region selection if one takes a look at Archer C1200(EU)_V1_170706 firmware.

Did everything from flashing back to Australia firmware to Unifi firmware/ Beta to Unifi firmware.

Still cannot

Can you teach how to enable?

Well....I am out of idea in solving your issue.


Meanwhile, I was able to enter the region selection, however, it can't save the settings.

I just want to flash back to UNIFI stock firmware,that's all. Anyway thanks

Let us know when/if it reboots. Mine rebooted this morning after 9 days...

https://forum.lowyat.net/index.php?showtopi...post&p=87680955

Replace basic_guest with workingMode



TFTP Recovery method?

http://tftpd32.jounin.net/

Immediately reboot when using samsung s6 connecting at 5ghz at 866Mbps to do speed test.



thanks

Seems like IPv6 not working correctly on the recently released non-beta firmware (Archer C1200(US)_V1_180103) for the C1200 US v1 model.

Not surprising the EU v1 beta firmware is also having IPv6 issues...

This post has been edited by biloxee: Jan 27 2018, 04:33 PM

Earlier error is due to I do not choose Malaysia (unifi) in the setting.

Now working ok after about 24hours. Wondering if this router is as good as d850 which goes months without need to reset.

However I do notice that with this beta the wifi signal seem to be lower then before. Seem similar to d850 which is not good.

just installed time yesterday. no wonder my router keep crashing

Darn. I finally know the reason of weak wifi signal as reported by few users!

In Malaysia; 5150-5350, 5470-5650 and 5725-5875 max EIRP are 1 Watt.
However, the beta firmware is using DE (Germany) power profile; 5250 – 5350 MHz (channel 36-64) is limited to 200 mW. Since the beta firmware only has channel 36 - 48. No wonder lah. Germany 5470 – 5725 has eirp of 1W, too bad beta firmware has missing channel.

According to Utilities Regulation and Competition Authority of the Bahamas (No idea why Time/TM/Maxis firmwares select BS as power profile, anyone wanna report to MCMC?), 5150–5250MHz is limited to 200mW, 5250–5350MHz is limited to 200 mW, 5470–5725 = 1W, 5725–5825 = 1W

Hope this concludes wifi signal issue.
If users are previously using higher channel with high eirp, after updating to beta firmware, weaker signal is expected.

Crash due to beta or original default firmware? Please be specific.

Original firmware.

Firmware: 1.0.0 Build 20171130 rel.34681 (EU)

Hardware: Archer C1200 v1.0

Seem like still no official fix from TP-Link for V1 right?

Yes, I can confirm that the WiFi signal has degraded with the BETA firmware.