Got battery that can do 80~100w single cell?

This post has been edited by KenC: Jun 21 2017, 06:37 PM

You are over pushing for your RM with " +juice".
it is possible to get complete set without juice at clearance sales or garage sales, but they don't come by everyday.

You can go convince mod manufacturer to custom a 80~100w single cell mod for you.

Or you can always use Mech mod… I think any Mech mod camdo that.

CFiber and CFiber Plus can do 100w but the wattage is set by coil ohm, unlike normal regulated mod. BUT it is built in battery, so you battery stockpile will remain as stockpile…

You asked for single battery 80~100w. CFiber are not, they are built-in batteries… so what you asked for don't exist that why you need to convince manufacturer to build you one. Btw, 18650 cell can't give you 100w safely… you need continous 30A battery for that, not max current…

Why I know, because I had been looking for one myself for a few months…

Just hang on to Mech mod, unregulated if you must do 80~100w with single battery.

This post has been edited by KenC: Jun 22 2017, 04:40 AM

85? You want 100!
Come to think about it why settle for 100w? Why not 1 horse power?

This post has been edited by KenC: Jun 22 2017, 05:27 AM

Any Artic Fox user?

KNS, my pico RDTA just die on me right after I completed my setup and testes… TNS! lived less than 1 month!!!

I reckon the board died… LED went black only…
open up visual inspection can't find problem… bring back to shop see how they say ler…

This post has been edited by KenC: Jun 23 2017, 05:01 AM

I was about to start playing with Artic Fox when my Pico die on me

I find RDTA easier to build and wick than RTA. The other handy feature is you can access to the coil whenever you wish without worrying about juice leak.

I tried planting tobacco in a flower pot many years ago….

Got a Serpent Alto to play. Spent a whole night figuring out how to wick it without leaking and flooding.
My 1st wick went without incident, beginners luck
The nightmare begins after that.
1st, leaks at the pyrex bottom, tried many things and eventually replacing the bottom o-ring solved the problem. 2nd, the airflow channel got flooded. Tried and tried all sort of wicking configurations, finally got the hang of it. I found that the wick ends need to be extra fluffy, just big enough to plug channel and just short enough to enter the channel, no need to go right to the bottom. No need to thin out too.
What I like most about the Alto is that semi-restricted airflow, MTL ngam ngam feel like smoking, and still capable of LH.
This tiny bugger is very thirsty! BUT that is ok as I brew my own juice.
Tried many cotton, meiji, kendo, shiseido, beacon… ended up using cheap steriled cotton ball from pharmacy, unflavored remains unflavored, clean, no dry hit however hard I tried. Only occasional spitting…
Cloud production is surprisingly good for a single coil, yet still can do stealth easily.
Can't comment on other flavors since I only do nic flavoured and unflavored juice. As this keep my coil and wick gunk free for weeks

This post has been edited by KenC: Jun 25 2017, 08:47 AM

[quote=nasrulbond,Jun 25 2017, 12:21 PM]
Did you try a little bit extra long cotton? Same thing happened with my kayfun, too short wick always cause leaking. Until i found a simple vid on youtube on how its done, then im good haha. And im waiting for 2 weeks for my Alto to come 😂

Btw guys, how often you did you drop your mod? After doing some inspection on my mod, i saw a tiny dent on the negative terminal compartment haih... i think maybe i dropped it once but only on thick carpet surface la but aiyoo.. but my mod still works okay i guess

I did extra wick length but that isn't critical, as long as the wick is long enough to go into the channel. I find that it is more important to have more wick to stuff up the channel.
Do you mind sharing the video? Never too much trouble to learn

[quote=nasrulbond,Jun 25 2017, 12:21 PM]
Did you try a little bit extra long cotton? Same thing happened with my kayfun, too short wick always cause leaking. Until i found a simple vid on youtube on how its done, then im good haha. And im waiting for 2 weeks for my Alto to come 😂

Btw guys, how often you did you drop your mod? After doing some inspection on my mod, i saw a tiny dent on the negative terminal compartment haih... i think maybe i dropped it once but only on thick carpet surface la but aiyoo.. but my mod still works okay i guess


I did extra wick length but that isn't critical, as long as the wick is long enough to go into the channel. I find that it is more important to have more wick to stuff up the channel.
Do you mind sharing the video? Never too much trouble to learn

Just wondering if anyone still using old school stainless steel mesh wick Genesis style Atty?

Looked up the kayfun 5 quick wick video, basically fold the cotton in. This will work if the wick is secured in place and not moving. I tried it with some success.

My Serpent Alto still leaks at the bottom glass seal.
This time I added an extra o-ring and it works really well. Now I can just hand tighten it without leaks.

I don't have a serpent mini to compare with. The flavour is intense! Also with good vapour. It is fairly easy to build once I figured out the wick. It is easy to build even with such small deck. It leaks and flood, you can fix the leak by adding an o-ring at the bottom of piece. The flooding can be 2 causes firstly are cured by proper wick and secondly a proper filling sequence, close the air flow control before opening the top cap, fill juice, lightly screw on the top cap, turn atty up side down, open the air flow, tighten the top cap. Then you can start vaping.
Don't over fill, don't fill over the top cap or you will have flooding into the air inlet.

I seldom do over 30w, mostly 9-12w, I only use vtc6, Lg HG2. But getting authentic is hard to come by.
I am neither cloud chaser nor flavor fan, just someone desperate for nicotine fix.