Hurry Hurry!!

Hurry for Mylarthree?

Hurry for the bi-flanges!

Looks like I gonna disappoint you with the bi-flanges. Currently no stocks, but let see what can I do this time.

bro...when u get ms2i...u will ignore the m3 lah...so no need so hurry lah


just kidding.

---

Added on June 4, 2007, 9:25 pmbro....
u wont waste the RM15
compare it properly, u wil find that the special of double flanges,

high isolation and clearer instruments

This post has been edited by yuheng: Jun 4 2007, 09:25 PM

Got my M3 from yuheng at 12.30 pm today...great guy man...will write a review once the 50 hours burn-in mark finishes...

quick first impresion compared to my first IEM (of that hpm70) that the soundstage is better...but will let guys know of the outcome later

just a quick noob question from me since i want it to pair the m3 with my treo650...is the m3 specs equivalent to that of m1 as follows :-

M1
Driver Unit: 9mm Mylar speakers
Frequency Response: 20Hz ~ 22KHz
Impedance: 16ohms
Sensitivity: 104db ±5db
Rated Power: 2mW
Max. Input Power: 10mW

I wanted to get a custom impedance adapter (either a 75ohm or a 150 ohm) but do not know which to choose not knowing about the m3 specs.



This post has been edited by iman_210: Jun 5 2007, 04:17 PM

infact i dont know the specs as well...can u be hold on ur purchases, i might asking the suppliers for it

and uncle wala, can help me to do this in this visits?

be hearing from u guys soon...tq for the prompt feedback

ok no problem. Which specs you looking for? ohms?

yeap ohms would be good...

seriously. if you run it from portable player / treo straight away. u think it can drive the earphone with extra impedance adapter? what is the purpose of you that want an impedance anyway.
u may ask scottiebaby how hard to drive his IM716 after adding a 75ohm impedance cable.
except u plan to use it with amp.
but from what i tried that day. tomahawk / govibe all can't power up im716 with 75ohm impedance. all of them max out only reach my normal listening volume, slightly lower maybe.
so scottiebaby forced to use PPAv2 which is not portable to drive it.

the ori treo 650 headset carries 32 ohm to its speakers...my worry is that would m3 be capable delivering even better than those of my ori treo headset.

yes i may be pairing the m3 and treo 650 with a portable amp that is why i the reason im thinking of getting the impedance cable.

---

Added on June 9, 2007, 10:22 amany update on this bro?


This post has been edited by iman_210: Jun 9 2007, 10:22 AM

soli bro, give ms sometimes, will go to supplier there around nx weeks

Time to flex your muscles and use your magic wand

how is the bi flange compared to the stock sony sleeve that comes with the m3?

considering of changing the stock sleeve for better isolation...

bro, the spec is similar to mylarone, the mylarone spec will be
Specifications
Driver Unit: 9mm Mylar speakers
Frequency Response: 20Hz ~ 22KHz
Impedance: 16ohms
Sensitivity: 104db ±5db
Rated Power: 2mW
Max. Input Power: 10mW

They are very sensitive IEMs. What are you going to do with them?

i have a pair of mylarone XB now,really impressed by the sound of drums, burn in now and i will do a comparison/reviews with mylarthree soon no later.

Heya yuheng,

Have been listening to the Mylar3 that I got from you and I have to say I am very impressed. I'm a noob so don't know how to describe what's so great about this IEM but I know I can hear details that I never noticed before using the Sennheiser PX100 and the sound is really nice.

So far have only gone thru around 6 hours of burn-in and will be doing more to see how the sound develops

Btw, here's a noob question.. how do I know I have the IEM properly fitted when I use it? I've not tried the different earbud sizes bundled with the Mylar3, the one it comes with I can wear although it's a little difficult to get a proper seal. And I don't know whether it's because I'm not putting it in properly or I need to use a smaller one.

Any advice would be greatly appreciated!

This post has been edited by Fyrekat: Jun 17 2007, 10:38 PM