too bad no Gerwalk mode
I like Gerwalk than Battroid mode except for Draken III Battroid, that one looks badass
ah the only kit I can see is Tomytech 1/144, too expensive because it is pre-painted kit

This post has been edited by nazrul90: May 25 2016, 07:24 PM

I actually went to the Gundam Base in Seoul. After conversion I found that the model kits there are more expensive than Malaysia. Not sure about the paints though. Technically they are flammable, so it would be best not bring something on board the plane which could blow it up.

The Efreet has cometh!

This post has been edited by xein: May 26 2016, 08:19 AM

I wish they can improve the skirt instead of following hg which only tilt front and not side way, it make certain poses looks odd

Btw more FA Gundam preview

This post has been edited by TheEvilMan: May 26 2016, 08:40 AM


Attached thumbnail(s)

You mean the front skirt or the side skirt?
The front skirt, you just need to separate the part into 2 parts. A simple cut in the middle did the trick.
As for the side skirt, it uses ball joints connecting to the back skirt.
The only problem is that the side skirt movement is restricted by the hose.
And the torso's is also restricted by the hose and by the skirts.



This post has been edited by xein: May 26 2016, 08:47 AM

Front skirt, even separating it they still only move front, happen to my GP04 and from efreet review it seems working the same way

At least give it a simple ball joint to tilt slightly to the side
When u try to open the leg wide, the skirt will looks odd
The pose u strike show the skirt tilting front instead of following the leg direction, that's what I mean

If it can tilt side way the pose would be more natural and dynamic

This post has been edited by TheEvilMan: May 26 2016, 08:47 AM


Attached thumbnail(s)

How much i can sell my gundam ?

picture below .

Just started working on Freedom 2.0

[attachmentid=6714350]

Ain't u getting the pearl coating + effect + decal set?

No, changed my mind on the special coating because no under gates. So if I sand, or do anything the coating will be affected. Plus not planning to paint this MG.
The effects purchased separately, only arriving in a few weeks time.

Last few days these 2 arrived

[attachmentid=6714462]

[attachmentid=6714469]

Now just gotta get the LED sets and find some time for it.
Got another shipment to collect tonight, different kits. Post picture later.

This post has been edited by refnulf: May 26 2016, 10:35 AM

All my wanted item will only available in August and Sept
Planning to get a RG sinanju too but wait for the review first, bought the weapon system hope the bazooka can fit the rifle (if It can fit neo zeong cannon then it will work for the weapon system product)

At this moment, I have the MG Gundam Thunderbolt FA, and the RG Sinanju PO'ed. Waiting for the MG Psycho Zaku to be announced also then PO that. Other than that, nothing else except some tools. Getting the RG Sinanju just to replace the HG Sinanju in the Neo Zeong. The HG version comes with the bazooka which shouldn't with the RG Sinanju kit.

Not too excited about anything else but you never know. Still waiting on some PG announcement soon, or in the next 3 years

This post has been edited by refnulf: May 26 2016, 02:13 PM

The System weapon work exactly the same as the neo zeong bazooka according to review, and the system weapon box have RG on it, so i try my luck that Bandai will honor their label, don't wanna regret later when the weapon system OOS already only search by that time (bet a lot of ppl will skip neo zeong and get the weapon by itself)

My reason for an rg Sinanju is to replace MG since my MG can't hold the bazooka properly anymore, and a small size like HG can easily perform this with help with support from any action figure stand like figma or SHF. Yet I don't po 1st cos i'm worry about the issues, seems every RG have some kind of issue of their own

Guess I need cement too to glue certain part, the astray and zaku was glued because places like side skirt or tiny part always fall out

Repose my MG sinanju while waiting for RG sinanju since it's gonna take months

This post has been edited by TheEvilMan: May 26 2016, 02:22 PM


Attached thumbnail(s)

Just want to ask any recommendation of glue can be use for sticker?
Working on Bandai's yokai watch modal, the sticker all like not in a good quality.
Really need the extra glue to stick the sticker on the plastic.

I just use normal super glue, the thin type (not viscous like UHU glue). So far never I've never had any problem.

Any specific brand? Some sticker does not stick well too in my case when it come to curvy area

Just picked these up

[attachmentid=6717949]

Now all the pg unicorn complete!

This post has been edited by refnulf: May 26 2016, 06:48 PM

Generic brands, and no problem so far even for curvy area. The problem with curvy area is mainly about the cut of the sticker, adhesive is secondary. Since Bandai designed the cut to fit for curvy area, stronger adhesive would help.

yea, i think their stickers is a lil too thick, even after i try to bend them and use my nail to pressure it down, it will still went loose, normally happen with tiny marking i.e: those marking on gundam head