Outline ·
[ Standard ] ·
Linear+
LYN OFFICIAL VAPING THREAD V30, - 30th Anniversary #VapeSmart
|
JimL
|
 Dec 8 2015, 01:17 AM
|
New Member
|
QUOTE(budakdegilz @ Dec 8 2015, 01:05 AM) of coz the rx200 sneak peak by youtube reviewer seems like it basicly still a ipvd2 with a new body design still doesn't work in low wattage setup and still no usb charger/firmware upgrade » Click to show Spoiler - click again to hide... « yihi chip is just an overprice obsolete hype product  Youtube reviewers never got the D3 with the actual SX150 chip. They reviewed the 'test' D3 which still had the old chip. I don't give a shit about step down. Want to vape at low wattage? Get an Ego. At least the Yihi chip doesn't jump out of TC mode unlike Joyetech mods which caused flames to shoot out of the drip tip. |
|
|
|
|
|
JimL
|
Dec 8 2015, 01:39 AM
|
New Member
|
QUOTE(olivur @ Dec 8 2015, 01:30 AM) Yep, mech wins all when it comes to headlines of exploding e-cigs! |
|
|
|
|
|
JimL
|
Dec 8 2015, 02:06 AM
|
New Member
|
QUOTE(gnomemaster @ Dec 8 2015, 02:00 AM) nak showoff imac lettew  » Click to show Spoiler - click again to hide... « btw, that black crown looks sexy on the rulo Psst psst....... ever thought of vaping at 200W? Try it and let us know. |
|
|
|
|
|
JimL
|
Dec 8 2015, 02:42 AM
|
New Member
|
QUOTE(gnomemaster @ Dec 8 2015, 02:18 AM) Loads of air flow needed. Like an Airek RDA. And fat wires or fancy coils. This post has been edited by JimL: Dec 8 2015, 02:43 AM |
|
|
|
|
|
JimL
|
Dec 8 2015, 03:01 AM
|
New Member
|
QUOTE(olivur @ Dec 8 2015, 02:54 AM) I resummon darth vader and the 200w materials![attachmentid=5468598] That a Mute? Go 0.2 in a Cricket and set new highs! This post has been edited by JimL: Dec 8 2015, 03:25 AM |
|
|
|
|
|
JimL
|
Dec 9 2015, 12:23 AM
|
New Member
|
QUOTE(budakdegilz @ Dec 8 2015, 11:04 PM)  next time get a Yihi mod *fixed! LOLOL |
|
|
|
|
|
JimL
|
Dec 9 2015, 01:03 AM
|
New Member
|
olivur nekkidgramma TristanX
A 'sleeper coil' would normally be built on a three post deck. Would it work on a two post deck? (Magma RDA 2 hole type). Or will it short?
|
|
|
|
|
|
JimL
|
Dec 9 2015, 01:56 AM
|
New Member
|
nekkidgramma olivur TristanX
Thanks guys. I had wondered because in a three post deck the wires attach to different negative posts.
Back to the drawing board if the resistance is going to be half. I'm just trying to figure out a higher resistance build for a dual coil RTA. The norm would be to use thinner wires or more wraps. I prefer to use 26awg and space in the deck is limited.
This post has been edited by JimL: Dec 9 2015, 03:19 AM
|
|
|
|
|
|
JimL
|
Dec 9 2015, 08:22 PM
|
New Member
|
kuli2sahaja
Has sourcemore.com shipped your stuff already? Haven't shipped mine yet.
|
|
|
|
|
|
JimL
|
Dec 10 2015, 01:02 AM
|
New Member
|
QUOTE(donatelo @ Dec 10 2015, 12:45 AM) hi guys, would like to ask about UD SS 316L, this is my second build, i build it in Lemo 2, and resistance i get is 0.6 ohm, i pulse dry burn to remove hot spot use tweezer of cause, is it really safe? and i vape in SS mode evic vtc , some said can vape in power mode as well but scared lol, temp control kick in no issue, with decent vapor and flavor as well, 20w @ 320f should be safe right? Pulse it till you get a faint glow. Stop after that. Hold the fire button longer & the wire snaps. SS wire is not a heating wire like Kanthal. Fire at 380F and increase from there. gnomemasterGift for you - turn off your RX200, then press all 3 buttons and hold for at least 5 seconds. This post has been edited by JimL: Dec 10 2015, 01:05 AM |
|
|
|
|
|
JimL
|
Dec 10 2015, 01:18 AM
|
New Member
|
QUOTE(gnomemaster @ Dec 10 2015, 01:16 AM) i really wanted the white one. but alexng only has black and i settled for it  Turn off your RX200, then press all 3 buttons and hold for at least 5 seconds. |
|
|
|
|
Quote
0.8468sec
0.73
7 queries
GZIP Disabled