brasso for brass / copper contacts is perfectly fine to remove patina. a wipe with isopropyl after removes any residue and doesn't scratch the hell out of your contact if you were to say, use steel wool on it.

as for using mineral oil on mods that isn't naked, know your mod. it isn't hard to figure out what works best for what your mod is coated with to protect that finish xD

Syukur, latest package of e-liquid arrived with no hassle from Custom (no nic and value of £84).

Pheeeew.

I've just took out the silicon sleeve off my SX Mini and its really gooey inside. Must be residue from juice leakage dripping down onto the mod. As suggested, I just wipe with soap and water.
Timely reminder to clean up your mod.
Anyway the sliver gray coating was scratched from before I bought the sleeve and really hate to look at it. Looking at anyway to wrap it like this guy does using 3M Dynoc.

This post has been edited by SZaid: Nov 17 2015, 04:50 PM


Attached thumbnail(s)

i saw someone posted about milkman here. any review?

tempted to try but im afraid its just not for me since i rarely vape creamy juice.

nice deal here
http://n9ne.my/product/one-hit-wonder-the-milkman/

the only regulated mod I kept is my rdna40 vaporshart and I just sharpied the missing paint bits that happens to all vaporsharts xD

could try using a silver marker and smudging it into the scratch and wiping off the excess with your finger

same. next month going lombok.

Contact support@shopee.com.my or call 03-22989222. Tell them your problem along with yr shopee username and cell number.
My friend flew to JKT 3 days ago...no prob with vape stuff...just observe the ruling on liquids, remove batteries from mod and store them safely in yr carry-on.

guys, need some advice.
I just got a UWELL CROWN Tank, and currently using the 0.5 OCC.
The thing is, it doesnt fire on my Vapor Flask DNA 40. It says check atomizer.
But no issue on my Radius.
I tried to adjust the 510 pin on the Crown, but still the same issue on the DNA40.

Any clue?

Thanks guys!

Guys whats the current market price for the brand new subox mini starter kit? I'm planning to vape because i need to quit smoking

around RM 190 before voucher discount, if you're lucky can get another RM 25-30 more discount before shipping

i've arrange groupbuy for OHW Milkman last week.. 3mg version..

for me, the taste is really good. you can taste the strawberry when inhale, when exhale got both strawberry + cream taste

am using it in kayfun lite.. 1.0ohm

come give testimony too gnomemaster budakdegilz Slinggg thecoffeeguy

Anyone mind explaining to me how safe is it to draw high watts from a regulated mod, say DNA200 chip. I'll be using 3 LG HG2s in it. The chip allows a very low ohm and lets say i build a quad coil at 0.2-0.25 and vape it at 120 watts. How do i calculate if its safe?

WORTH every penny considering it's half of what usual US liquid's price, its flavor definitely justified.

and yes, i use solely on my RDA. dual coil 0.4ohm gives me decent flavor

when next groupbuy again? can count me in again

but dono y when i leave it overnite the juice on the cotton turns red

try this. but don follow it blindly....

http://www.steam-engine.org/batt.asp

just ecf giveaway Evic VTC,

guy, SS 316L should be use in power mode or temp SS mode? anybody try6 SS 316L yet? still waiting from fasttech, regret use china post hard to track lol

Thats the problem, I have no idea what the page is talking about lol. No knowledge on voltage etc..

Wattage mode?

Does it work with 0.15 ni200 occ?

after u key in the variables u know, u look at the amp limit headroom, to be safe always keep it above 20% unless u mau risk lol.

but but i don think HG2 shud go this low...sounds risky.

it's safe, since there're three 18650 cells it replicates the 3 cell lipo packs most slimmer dna200 devices uses

if you vape constantly at 120w, once your battery drains and is unable to push that much it'll just give you a weak battery message c:

check out pbusardo's three part tut on the dna200 chip. the one thing you might wanna set is the internal resistance for your mod to get a more accurate reading (which vaporshart actually did for their dna200)

other than that it's basically just know which wires goes for which mode and plug and play c:

also download escribe!


addendum -
remember to marry those three batteries. use them only exclusively with each other, as well as charging those 3 together to try and get a gradual decrease as you use them

This post has been edited by olivur: Nov 17 2015, 08:03 PM