Hi,

For you hardcore C2D guys - what is your mobo temp and what are your idle/load temps using stock Intel cooler (measured using coretemp, Intel TAT or Everest only) ?

I need to poll as I think my ambient temp is quite high (45C, warm room) and I'm thinking heat is a big problem.

THanks!

This post has been edited by Diademz: Oct 31 2006, 04:15 PM

my E6300:
1.866Ghz -51C~ idle. 56C ~Load Orthos
2.800GHz- 55C~ idle. 59C~ Load Orthos
3.050Ghz - 60C ~idle. 64C ~ Load Orthos

hi yehlai,
those are very nice temps. what is your mobo (ambient) temp ?

my e6400
3.28ghz idle:62c,load 78c

mobo i dunno yet coz i only use TAT..
dint use mbm or ET5.. i think below 50C

What softwares you all use?? I got many kinds of reading using different programs.. and i think core temp and TAT is much trustable..

[Mobo bios (Gigabyte GA- DS3 F6 bios) - 42C
Speedfan 4.31 - 41C
Core temp 0.93 - 50C
Intel TAT - 52C

When under 100% load under TAT is 65C

While the Maximum Thermal Specification according to INTEL for C2D is 61.4°C, this is considered the maximum temperature for the CPU.

I m using everest ultimate edition 2006
the mobo temp is 34 and the cpu is 50, core 1 48 and core 2 50.... this is under non air cond room and my clock speed is 3ghz

this is my temp when cpu idle, 3200Mhz at 1.325v

thanks guys!

elmoboy, coretemp and TAT measures the temperature of the diode in the CPU itself, so it's the most accurate (and hence higher readings compared to eg speedfan).

This post has been edited by Diademz: Nov 1 2006, 01:29 AM

Hi,

I just got a e6400 and a Gigabyte DS3, using the stock Intel cooler.

In the BIOS under PC Health Status I set the "Fan Speed Control Method" to DISABLE as I want my CPU fan to run at full speed.

Now I undervolt the CPU from stock 1.3V to lower e.g. 1.23V as I want to reduce my CPU temp but I notice that the CPU fan speed also reduces in RPM even though it's not supposed to(eg from 3000rpm to 2500rpm). As a result the CPU temp is still high.

Apa macam? On F7 bios - is anyone else having similar issues?

Thanks!

So the Maximum Thermal Specification according to INTEL for C2D at 61.4°C is measure from where?

i think there is a temperature sensor on the fan .

My fan speed runs at lower RPM regardless of whatever setting that I set.

I'm running mine at around 3Ghz, with two instances folding@home running, temps is more or less around 61C.

*measured using CoreTemp software.

This post has been edited by c9: Nov 1 2006, 07:26 PM

Nice temps c9. what is your mobo/ambient temp, and you're on the stock Intel cooler too ?

Mobo is DS3, and yeah I'm on stock Intel HSF. Ambient roughly around 30C-40C, I'm using a Lian Li V1000 Plus by the way.

This post has been edited by c9: Nov 2 2006, 03:41 PM

omg i need to find TAT and coretemp.... i use that easytune 5 give me funny results.... idle 37 only

Ok finally weaned off Orthos for stability and just started both cores folding. Temps are much lower than Orthos @ load, much like yours c9...about 62-63C vs 68C for Orthos.

thanks again!

my new coretemp result:
idle: 59
full load(after Dark Crusade):62

on stock HSF....

This post has been edited by t3chn0m4nc3r: Nov 10 2006, 08:33 PM

(after Dark Crusade) is not full load...try use Orthos to prime...