Yea, i even compare the humidity sensor with my Sharp air purifier, though just 1~2% differ but satisfied

Havent play with the scene mode or IFTTT

Still noob level right now.

I just did simple stuff like alerts when temp and humidity exceed certain threshold. nothing fancy

Oh, the routine / scene mode?

Belum play with it, haha

Still thinking wanna integrate with IFTTT or not

Go for it and update us here. 👍😁

I guess depending on your auto gate... do you need single channel or 2 channels?

for 1ch, you can go either Sonoff or Tuya.... for 2ch, better go for Tuya

Sonoff 1ch
https://shopee.com.my/DIYMORE-Sonoff-WiFi-W...0449.2579118027

Tuya 2ch
https://shopee.com.my/Tuya-2CH-USB-DC5V-7-3...2258.6943994787

EweLink also have 2 channels
ewelink DC 12V 2Ch

Beside the HTS2 sensor can be equipped by Broadlink RM Mini 4,
Actually any other big difference between these 2 except supplier name?

1) Mini 4 by FastCon
2) Mini 4C by BestCon

Both supplier name really funny ..
Faster Con ppl?
Best Con ppl? :lol

Hello..Anyone knows if it's possible to change this aircond switch to those smart switch?

Any recommended system to use if I want to explore changing my wall switch for the fan (old fan) and light (fluorescent) in the room. Quite like the Xiaomi Aqara but the plug point seems to be an issue for certain items like the gateway hub/smart plug/ etc as I'll need to get a converter.

LOL, come to think of it

Anyway wta

This is the innards of the 20a switch, anyway to tell its upto 20a from the pic?

This looks like old 1hp aircond installation, right? Nowadays 1hp do not use starter like this anymore.

That Red and Green button is actually just simple switch to trigger the magnetic contactor inside the box. It is just momentary switch.

What is your air-cond horse power actually? How old is your air-cond?

I have changed my aircond before. This starter was for a much older aircond. The current one also probably has been about near 10 years I think and if not mistaken it's 1.5hp

Those who use smart switch for auto-gate can advise since it use momentary contact. Normal switch will just either on or off only. This can be done to simulate pressing that Green and Red button.

I have this as well, but the Ewelink variant. I think on the back it does mention right? But so far I have installed 3 of these "20A" switches one of which is the heater the other 2 for water features. No problems so far.

This is the front only, IINM for low voltage. For high voltage is at the back of this board

Those smart switch for Autogate normally use 10A relay. Don't think can use for aircon unless got higher amperage?

Mini 4c not compatible with hts2

Why not since it is just used to switch on contactor switch. The actual load is on contactor, not on the push Green and Red switch, right?

Ah, OK I understand. Then should be OK.

Ya bro, on the back it does say 20a printed on the plastic casing, reason I ask is bec there were 2 online sellers who told me there were some with lower amp, cant remember was it 10a or 16a, looked the same but slightly cheaper, just wanted to confirm and also make sure those who buy are aware. I have installed both Ewelink and Tuya, difference is Tuya can set off delay, as in wait for AC to completely shut down before the 20a switch shut off so I can use GA to switch on and off both via routines.

This is what I see at the back, thought there would be some resistor or something with 20a. Anyway doesnt matter. Thanks.



This post has been edited by cablesguy: Sep 8 2020, 04:27 PM

Wow, I did not see anything that handle 20A here

Just a single piece PCBA with front and the back just like that?

Looks like they put extra solder there for higher current.

Yea, aside from that, there is no other differ?