just got my Opty 146 (2GHz), PNY 7600gt, DFi NF4 SLi and Sunbeam 550w NUOO series last week....
till now still try to get the most of it mainly at the proc & mobo segmen... needs some advice out there maybe this setup can do more than wud currently i got

the full specs are:
AMD Opteron 146 (2GHz, 1MB L2 Cache) @ 2.76GHz, 166MHz Divider
DFi Infinity NF4 SLi
Kingston Hyper-X 512MB PC3200 (Windbond CH-5 chip) @ 230MHz, 2-3-3-8
PNY 7600GT DDR3
Sunbeam NUUO Series SLi 550w

below are my latest screenshot since last night...

Abit KN8

Hi , I've just have change my pro to a 3500+ . How high can this baby go ?

hi there, I need your advice as to determine the correct memory divider in making DDR-2 667Mhz running its full speed, I am using Athlon 64 3000, clocked at 2000MHz

I just want to let the RAM running by its maximum speed, I dont want to modify vcore or FSB/HTT settings

err.. all sifus.. i'm new to A64 939, got myself a 3700+ san diego on Asus A8N-E recently, tried clocking it to 2.4Ghz, booted up properly, but then when i check it thru system properties, it shows 2.2Ghz, check with CPU-Z, it shows 2.2Ghz too.. but when i check with Asus Ai booster, it shows 2.4Ghz like what i set in bios..  this doesn't happens to my other A64 at home(3000+ venice on A8N-E too).. anyone knows what is wrong here?? was it with the Sandiego or ??

Can teach me on how to do it ?

hehe... those rails actually i'm not fully mapped it with actual sensor yet... just install mbm and go.... i dun think a SLi certified psu would do that  anyway the rails are great in CMOS

What's the best way to burn in a chip from u guys experience ar? I've never had to do burn in coz always been lucky to get gem CPUs that OC like hell straight from the box.

This time not so lucky. My X2 4200+ oni can max out to 2.42ghz dual prime stable at stock voltage. That's y I've been burning it in by dual priming for like 12 hours, stop to let AS5 settle, then dual prime 12 hours again, on off on off like that. How long shud I burn in b4 pushing for more FSB again? I've read that we shud burn in for bout a week, then push FSB, burn another week, push FSB again in that order until u c no more gains in FSB.

can anyone help me with my sempron 2600+?

at 9 mutli..i cant go more than 285 at 1.7v..ldt set to 3..is it because of the mobo or proc?can u giv me contact num..ym?easy to chat..thanx bro

i dun think its memory prob coz the speed now is at 200 with stock voltage..the highest i can go without memory error is at 230mhz..now i'm trying new setting ..the voltage for the cpu in bios is at 1.58v for this new setting when error occurs..do i need to add more or is there other way? or izit temp issue?

I got Prob Oc this rig.. Whenever i increase it Frequency it will start to hang.. Dunno y hard to OC this rig.. Can any sifu teach me as im new in amd..

TCCD won't like high voltage.  Some people spoiled their TCCD after running with more than 3.0V for a while.

I would say the safe range would be 2.8V - 2.9V. The lower the better.

TCCD run damn hot at high frequency...

Got conflict with the bios and the oc guru..If  Setting in bios, cpu-z still show the default settings.. Need to uninstall the oc guru? Better use oc guru or manual?

my TCCD running daily at 2.83V @ DDR640 (320MHz@3-4-4-8)

guys...

my winchester 3000+ having prob to push 2.2ghz.. prime failed after 45minutes... damn.. b4 tis im using 2.2ghz for 5 months already!... already prime 16hour stable.. but when last week i format my pc.. after revert to default.. make sure the stability... im try to oc again.. set to 2.2ghz.. but when prime... always failed...

my setting :

244*9
HTspeed x4
dram 166mhz 2-2-2-5
1T

my board cant change the multiplier.. s**k it...

any help?

You are right. Mine is AAA. But, forgot the week production d. AMD64 3000+ 2.6GHz @stock vcore.  What do u think?
Never thought got CHINA made b4. But I got it 

bro.. my mobo lock the multiplier... cant change downwards....

how to check my nominal/default CPU voltage? where to find the info?
cos the value in CPU-Z keeps shifting between 1.376 and 1.392v.

after i found out from OPN, it's 1.4v. why so big difference between 1.376v?

where to find info on my PCI frequency besides BIOS? any software?

Quote from Overclock.net

i'm using a nForce 410 mobo.(those with built in 6100GPU, i have a dedicated graphics card anyway) it doesn't have the lock options in my BIOS. does that means it is lock?

no la..  no option for multi.. huhu.. but my prob is can oc my cpu... prime always failed after reformat... maybe i need to reformat again?

hai.. is that really o.k to run cpu with vcore 1.545V for a long term bcoz currently i ran at that voltage somebody say it is safe as long as vcore lower than 1.625V...
Right now i manage to get 9x290=2.61GHz...8+ hour prime test without error with large FFT and ram prior at 4....
Has anybody got bad exprience when run Vcore above than 1.5V for along term..

For Snipper69..
i really want to know.. is that proc really o.k to run below than stock vcore or only certain proc can run vcore below the stock vcore like ur proc..

i use stock cooling, here my cpu temp :

idle : 42
full load (while prime test) : 55

is that temp ok or i need to replace my cpu cooling to run at that vcore for a long term..

Alrighty.
Used three motherboards, socket 939 till AM2, all of them won't let me boot at 280HTT.

MObo : Abit KN8 Ultra V1.1
PRocessor : AMD Athlon 64 3000+ .. Venice ..
Ram : kingston DDR400 PC 3200 512 mb X 2 ..
GC : Colorful 256 mb DDR3 7600 GT ..
HDD : WD 160 gb SATA2 ..

just thinking whether can oc or not ..
i guess the mobo not that good lor ..
and i dun have a cooling system also ..
if i wan OC , i think i should get ram cooler and better heatsink right ?

really good at OC-ing ..?
ur specs and mine about the same ..
except for ur motherboard .. lol ..
u planning to OC too ?
but one of my buddy say the motherboard capacitor no good wor ..
anytime can leak one .. sigh ..
anyway , can i use a higher DDR besides DDR400 ??
if can i plan to sell of my ram and get a faster one ..
and do i need to get better heatsink and ram cooler ?

1. If u think u wanna bump lots of vcore, so u better change ur hsf
2. If u just wanna do some mild OCing, just stay with ur current ram
3. U can OC using kn8 ultra, but for better overclocking, use DFI is

s-940 use ddr1 with ecc

s-AM2 use ddr2 

not necessarily. higher clockspeed will contribute more heat. if you pump higher voltage at default speed (example 1.8ghz on 3000+) the temperature is not much different... probably only around 2-3'C higher.

I tried overclocking my rig yest with core centre i'm using nf4 ultra plat together with x2 4600 939 and 2gb value ram.

it is ok ah? My temp will go highest up 50. My core i have increase to 1.75 Anything less than that, it will restart itself.

http://valid.x86-secret.com/show_oc.php?id=148100



CPU : AMD Athlon 64 X2 4600+ (*1)
CPU Arch : 2 Cores - 2 Threads
CPU PSN : AMD Athlon™ 64 X2 Dual Core Processor 4600+
CPU EXT : MMX (+) 3DNow! (+) SSE SSE2 SSE3 x86-64
CPU Cache : L1 : 2 x 64/2 x 64 KB - L2 : 2 x 512 KB
Core : Manchester (90 nm) / Revision : BH-E4
CPUID : F.B.1 / Extended : F.2B
Freq : 2664.24 MHz (222.02 * 12)
----------------------------------
MB Brand : MICRO-STAR INTERNATIONAL CO. LTD
MB Model : MS-7125
NB : NVIDIA nForce4 rev A3
SB : NVIDIA nForce4 MCP rev A3
----------------------------------
RAM Size : 2048 MB
RAM Freq : 222 MHz
RAM Type : DDR-SDRAM Dual Channel
RAM Ratio : CPU/12
RAM Timings : 3-3-3-8
----------------------------------
Slot 1 : 1024MB (PC3200)
Slot 1 Manufacturer : Kingston
Slot 2 : 1024MB (PC3200)
Slot 2 Manufacturer : Kingston

very high voltage 

btw , i'm trying to get A64 ES   . any opnion ?

is there any different with batch dh-e3 and e3???
i can only  oc to 279 fsb...
with 1.6vcore..