Loll.... ME fanboy... Anyway i choose ME too but Mr. Slim version.

No worried, in JB close to Sg that is why the 1st batch always imported from sg.

The 2nd batch already direct from thailand that is why change name into Mr. Slim

thanks for the spec sheet.just got one from dealer. showed msy-gf model.
the one u showed is few months ago?

mr slim is ME or MHI model?

Huh we never talks about MHI at all.

All my photos showed on Mitsubishi Electric and never showing the on Mitsubishi Heavy Industrial.

Both are using same logo , but different company.

Once you get confused, nothing can help up.

This post has been edited by kimsim: Jan 21 2015, 04:09 PM

What is the normal rate on putting an aircond/moving an aircond?

Input watt or what?

I need to move it slightly away from the current position. The input watt is 1080 if I m not wrong.

Gas pipe can't moving away.

Unless they help you connect the copper pipes

oh ok thanks but do you know how much it gonna cost like what you stated?

Thanks

If wanna remove whole FCU and put to new place and drilling hole also, I guess is around Rm180

Thanks for your input.

ha ha

your brochure u showed is few months ago? now newer model?

but i saw in the new brochure did not say mr slim. is mr slim sg model?

This one took from S'pore one, just the 1hp & 1.5hp change to GJ model in M'sia only.

Like M'sia got premium specs come with eye motion and S'pore don't have and they have Zen model in S'pore only.

Anyway you can collect from some ME website recommended Aircon shop.
http://www.mitsubishielectricmalaysia.com/...ircond/inverter

so 2hp & 2.5hp older indoor unit, not slim model? 1hp & 1.5hp "GJ", 2hp & 2.5hp "GF". "J" is after "f" so GJ newer model??

2.5hp outdoor unit lighter than the 2hp by 1kg?

Actually from 2 to 2.5hp inverter never changed since the design and specs from 7 yrs ago.

In M'sia just rename as GF only, cause Mr. Slim how can be used the same naming as Starmex.

Not too sure about 2hp, if you really concern about more cooling and power the better choice with 2.5hp can save more energy than 2hp, just worried it would be underpower on your living room.

This post has been edited by kimsim: Jan 21 2015, 05:33 PM

to install in gnd floor and have staircase leading to upstairs.so will have leakage of cold air.

thinking of installing curtain to block off cold air to upstairs, is that a good idea?

Don't worried cold air away going into ground.

Like my common bedroom, is 5.2m height and upper ceiling got opening window.

At the room will slightly slower cold down only, once getting cold the amount would be same like normal 3m height enquvalant

My kitchen also open, so you just concern about living room area keep it cold then good enough.

The idea you can install direct blow to sofa area, more save energy.

This post has been edited by kimsim: Jan 21 2015, 05:48 PM

my living room window has opening for top part of the glass meaning about 6" opening (near ground floor ceiling). was concerned if i need to seal off the opening.it has mosquito netting there.so no need to seal off completely?

cold air travel down.but if there is strong wind, outside air can blow inside will affect air-cond,right?

Ya correct cold air travel down

Opening not enclosed, the strong wind can easily bring dusty air all the time, so ur fan coil blower have more chance to getting more dusty at all.

Anyway if enclose opening from outside much better to block some dust from outdoor.

This post has been edited by kimsim: Jan 21 2015, 06:10 PM

Other than those franchise shops which asked contractors to do air-cond installation, any good contractors/shops in Penang ? Looking to install either 2hp or 2.5hp unit. Thanks !