NMGH you win liao....I nothing to say...like David said someone higher ah...

My front lip not yet pasang, no time yet. I only manage best time 1.15 at MIMC....T_T my parada spec2 overheated...hahaha but parada very lasting...survive quiet some track days and time attack...

This post has been edited by TitanRev: Aug 23 2014, 06:23 PM

I'm happy with what I have because I'm not looking to break any Guinness book of record...hahahaha. Having more power is a plus point but more importantly is how one can understand and fully use the available power to his/her advantage. After all dyno figures are just numbers on paper, how to apply those figures in real is a whole different thing.

Enjoy your fun time that day....take some pics too....I want to see....

Why not...

bring tuna sandwich.... I think the others who go there can help look after each other.

Why you no join.....test the Ecopia...

Can DIY the EL light bar. What you need

1 LED any colour you like
2 Translucent flexible PP strip (like those use for cutting grass) ACE ada
3 solder gun + tin
4 reflective foil tape. (to tape the joint to the strip) ACE hardware banyak
5 resistor
6 shrink tube
7 wires

Step 1.
Calculate the high power LED voltage consumption then get a appropriate resistor then solder resistor to + leg of LED. Then solder red wire to resistor and black wire to "-" side of LED.

Step 2.
Use shrink tube to cover each soldered point and use hair dryer or heat gun to shrink the shrink tube to protect the soldered area from water and short circuit.

Step 3.
Put another layer of shirnk tube bigger size to cover the bottom of LED and the wires.

Step 4.
Use sand paper to sand of the rounded head of LED to make it flat. Attached the flexible strip with glue and wrap the joint area with silver reflective tape. (Wrap the whole LED) reason is do not want the light to leak out from the side and all light will travel into the flexible strip. Also sand the flexible strip so that the surface all become translucent.

Step 5.
Repeat step 1,2,3,4 for the other end of the strip. ( you need to calculate the length you want 1st)

Step 6.
Joint the + wire of both LED together with solder so that 1 wire can power 2 LED. DO the same for the "-" wire.

Step 7.
Connect + wire to parking light + wire then "-" to body or parking light "-" side.

Have fun trying...

I believe I go China sure can find a lot of these. I also just bought back quite a lot of LED from ShenZhen...

Try do for interior 1st if not sure...

Wah lan eh.....

Come DIY with you....I ada heat gun...

1 word........SEALANT.....cukup...

Smoke enough la...apa AUDI like...want AUDI lookalike pigi beli AUDI terus....

You no need to buy paint my house have....your car old already the sealant need to change la....apply new layer...

IF can get like this nice..


Just my own idea how to install EL or those light bar to FL headlights to be nicer...
Either Like this


or like this. Or maybe proton designer can replace the sighnal bulb section to be fog light like on the A31. then use LED light bar as signal....

macam mana?

Parada Spec2 -- not bad and price also cheap or if you want better see my avatar...good tire..price also less than 300/pc

you la

Please see his post...he states PS3 sudah....PS3 is in that price range....so he can afford it....faham??

iskazulka still not cheap enough?? for 15 inch??

Not very noisy to me....in wet not bad but I the max I tried on wet was going 140 and run over water puddle. The car aquaplane a bit and steering feels light so after that I tau the limit. my current RE002 is better though. Hit water puddle can still give slight steering input and the car still can steer...in term of ride harshness RE002 is definitely much harsh than spec2 now my car cabin is more noisy and feel like rolling on tires filled up with stone inside...

Summon you for what?

Ok ok, how many square mm face you want?

But use parada go track quite fun. Tire is cheap and won't so painful to wallet. It can't compare with those higher end la but at least still can use on track or time attack. they last me until 37+k mileage before I have them changed. The time I replace them they still have a good 50% thread on all 4 (thread wear was even and only the shoulder makan more only) and I gave to kenji Lew and he further use them at superlap some more...the parada has tasted SIC, Elite and MIMC. The down side about it is the soft sidewall and overheating but if you do 2-3 laps and stop to cool down also can. Value for money performance tires I would say.

This post has been edited by TitanRev: Aug 28 2014, 03:54 PM

Then take parada spec2 la....cheap and cheerful

No offense, but PS3 I found it so so only...for daily use ok but not for the track.

But I don't see much PS3 even on small tracks. Mostly using SX2, R1R, NS2R, RSR..PS3 very seldom can see it....