Yup..ada hikmah la kot..

Luckily the system is still up and running after I clean up the oil spill..currently using my other PSU (for my next build)..pinjam kejap..Please ignore the cables..



Already buy another Silverstone Strider Gold (SST-ST65F-G) but this time I wont do the wiring again..I bought Silverstone Short Cable Set (SST-PP05) for safety..

I suspected my wiring have shorting somewhere..noob wiring..

I need to practice more..

But when I dissemble the PSU..nothing seem leaked..all the capacitor still intact and look good..

Maybe it really came from the fan fluid bearing..

I don't think I can send it for RMA..because I already dismantle the PSU..automatically that will void the warranty right?..Huhh..I purposely build this PC for my wife..but too many things happen..hopefully after I replace the PSU and use the prewired cable, everything will go fine and working..

Too much has been spent for this build..the budget should go to my build..

This post has been edited by orion_xtrmx: Jun 9 2014, 09:06 PM

The custom reservoir couldn't contain the fluid..it leak bro..




I bought it on lelong.com..but yesterday the seller offer me to upgrade for PP05E..I bought the PP05 for RM75 and need to add RM25 for the PP05E..

This is PP05



and this is PP05E



This post has been edited by orion_xtrmx: Jun 10 2014, 10:28 AM

First I also plan to get those reservoir..but always don't get the chance to grab one..huhu but now I'm perfectly fine with the Swiftech MCRES Micro Rev2 Reservoir..

Thanks bro..it really do contribute a lot for this build..hahaha..I'm currently waiting for the PSU and the cables..hope by this week I could complete it.. will focus more on my own PC..

Hi guys..

Little update and I think the finish project..haha

The replacement PSU received on 16/6/14..together with the PP05-E short cable for Strider Gold Class PSU..





So I install the new PSU and the system is running fine now.. Temp CPU 37C and GPU 36C..Maybe later I'll plan to use Potted Peltier





Notice that I try to change the coolant color to red using Mayhems Deep Red Dye but it is a failure..

May I'll change the side panel acrylic window because the current one is quite full of scratch..


My finding regarding the previous PSU failure is that... I think I have put too much load on a single molex connector..all the fan controller, pump and the CCFL using a single molex..Don't know..just my thought only..

Bro PM me your address..I'll post it to you on Monday..you just pay for the postage bro..

Hello...

I know that this project shall be considered done already..but I don't think any future modification will harm anyone right? So I would like to post some update for this project..tangan gatal already takde keje..

I tear both side panels to replace it with the transparent black color acrylic sheet..See the glue residue after I remove the panel..



Also do some paint job left from last build..





This is what left from my prodigy build..so I use them..



The end result..





HEHEHE..

The original coolant that was used on this build was Armaggeddon Water Cooling Coolant ARCTIC FUEL 1000 (ACID YELLOW)..but I add some Mayhems deep red dye to make it red..but it turn out hideous
So I plan to change it to UV Green by EKWB..I also change my CCFL setup from white to UV..

The UV CCFL..longer than current CCFL..



The white CCFL



I remove the PSU and will drain the loop..but...no drain valve.. ..huhu see the coolant's color..



After the coolant is drained..I clean all the tube but the plasticizer is too hard to peel off..just look at the reservoir..sorry forgot to take pictures on the tube..



So I decide not to reuse the tube and replace the loop using the acrylic tube..since I have extra fitting from the prodigy build..

Sorry no picture of installation....but look also add a drain valve by koolance under the reservoir..



The end results....











DONE...