ya i copy...but already delete data that save in txt file...then runing it again...but if i copy the result of 1m super pi must got the same result rite???correct me if i totally wrong!!!

3800 i think can go to at least 2.9 with some good tweaking la.. try it out... hehehehe...

2.5 onli aa??
didn't try to go up to 2.7 like sempronic proc aa??
try la... u r using the same cooler as he is...

im using TR XP90c onli... if full load my PC will be a heater u know... u can feel heat from the PC... when it's raining and cold outside its good to have a heater near u... hehehehe

adjust the vcore a lil bit higher laa... mine is 1.48v @ 3003mhz and vdimm is @ 1.95v... idle @ 38c full load @ 55c with TR XP90c + Delta 92mm Fan... hehehe

u guys try la @ least 1.3-1.4 then maybe can go up till 2.7-2.8...
when get there, prime then lower it back to 2.5 la... onli so that u guys know how high the clock can go onli... for future use also.. hehehe

mine cannot boot edi lor at 2.7Ghz...edi pushed vcore to 1.550..
even at 2.650Ghz cannot pass PI 1M calculations edi.. 

65w and 89w OCbility differ.. especially on voltage needed..

i've tried until 70C edy..
i think 60C refer to core.. sometimes unstable system not caused by temp or reached the wall... but over voltage also...

last time i need 1.55v to set 2.6ghz.. after a few burn-in 1.5v is ok...
right now.. 1.48 also can stable..

just use the orthos also can.. leave it for few hours..

i think for ur case not becoz of the cpu cannot go far.. maybe the ram divider is not right... and htt exceed 1000.. depends on mobo though...
reaching 260fsb i set 3x htt mul...

cpu also need a little training... like motorbike.. always need to full trottle to make it faster... after sometimes it will get use of it...

wow...u managed to change to lower timing with ddr800? thats a good result.
i havent tried it yet...still stick with 5-5-5-12

so hows the superPI result? improved a lot?

Fellow am2 brothers! hehe

any good ocing board to recommend? must b able to go until at least 2.2/2.3v vdimmlar...thinking of biostar tforce 570u lar..any other good ocing boards out there especially gigabyte boards? and any idea how much the biostar tforce 590 sli is? thanks so much guys..appreciate it!

Just wanna make sure something, is my OC method correct? Using AMD 3000+, Gigabyte S2G and 667 1GB RAM. Noob in this OC stuff

Here is what I do at BIOS:
1. HT set to x4 = 800MHz
2. Set DDR 667 to 400 -> ratio 1:1
3. Multiplier x9
4. Increase core speed by 10MHz maybe
5. Load windows
6. Check stability with OCCT, cpuz and also CBId (didn't support vista )

I manage to do until 256x9 = 2304MHz. Stable and didn't really have the guts to do further since I'm only using stock HSF.

avoid anything else except those 4? what about Gigabyte? I don't have a clue why

currently running 2.5Ghz@1.275v..
full load temp just around 36c aircond room..
quite satisfy with this NT06..

my brisbane aso arrived..haha will get it tortured later on 

yes..1.3V but the reading surely not accurate at cpuz..it iwll jump n down

running 265 now @ 1.325 vcore..will test further later on..idle temp around 34C n load at 39C on my noctua NH-U12F..temp from thermal probe

-pWs-,

nop..set to 1.325 from 1.3

like dat only i manage to get it stable 

now doing 270 still 1.325 vcore

the abit kn9 ultra hav issue running my ram in 667..drop to 533 everything run fine now 

sry, can i ask which program u all use to c the vcore? since the cpu-z is shot shot. is it 3800+ run at 2500MHz by 1.525v is normal?

Im slow. Brisbane in stores already?

Iyer ler i know i been a bit slow.. I been swamped with things to do only recently had the time to tweak it a bit... If i had used an aftermarket HSF like ur Noctua i think i'll try to push it even further..   Don't want to have a burned CPU yet ler.. but lookin at the brisbane O/C result makes me kinda itchy alredi.. Hehehehe

holy moly.. using stock cooler or noctua.. must grab 1 la like this..