Btw, just a quick one
I recently got myself a scout 2 casing, really really love it

at first was surveying between HAF912 (RM285)
CM690 III (RM350)
Scout 2 (RM288)

finally i went for scout 2, wished they had white one but i still love it and modded the top removeable air filter holder to bright orange

Of the 3 models, Scout 2 is really really worth it for the price
this thing is really well built - tough is the word

Comparing the 3 model side panel toughness
690II the most flimsy one (but still in the mid tough i would say)
HAF912 has a very rugged side panel
Scout 2 - this side panel is really really tough, can only bend a bit, full metal

Hi heerosakura, we'll take note of your interest in our Control-RX pad and voice out to the person in charge.

Hi Shoot@M3, thank you for the feedback on our casing.

would like to know the ETA for the Nepton 280L.
Tested the Nepton 140XL and was satisfy with it.

Hi lucidlts, we are currently waiting for the update as well.
If you've been following FrostyTech's update for the best AiO Liquid Cooler, you can see that our Nepton 280L scores the best: http://www.frostytech.com/top5_liquid_heatsinks.cfm
Not only that, it received a lot of positive review from famous tech sites such as TweakTown, Tom's Hardware, Overclockers Club and more.

Frosty Tech - http://www.frostytech.com/articleview.cfm?articleid=2752
TweakTown - http://www.tweaktown.com/reviews/5911/cool...view/index.html
Tom's Hardware - http://www.tomshardware.com/reviews/nepton...ax,3607-11.html
Overcockers Club - http://www.overclockersclub.com/reviews/co...er_nepton_280l/
Benchmark Reviews - http://benchmarkreviews.com/8188/cooler-ma...-cooler-review/
Gadgetop - http://gadgetop.com/cooler-master-nepton-2...w/#Introduction

This post has been edited by CM.Storm: Feb 23 2014, 01:58 PM

I've done a review for the CM Storm Mech recently, hope you guys like it

wa, transition to video reviews liao I see

test water first

Hi lucidlts, thanks for the brief review on our CM Storm MECH gaming mechanical keyboard. Keep up with the good work

Thanks
Back to the previous discussed topic, the 280L seems to be winning the performance competition but not the silence competition.
You guys need to put more effort in fan design, more airflow, higher static pressure and most important is, the noise control.

Hi lucidlts, thanks for your input.
Yes we are aware of that and our team is working on it to provide the best solution to everyone.

on the mech keyboard side, some serious suggestions from the LYN mechkb community (mechanical keyboard enthusiasts discussion group) are:

1. no more non-standard layout on the keyboard already, please~ seriously on the modifiers
2. take out that rubber coated surface build on some of the models, but i cant remember which, but quickfire rapid is one of them
3. costar stab or cherry mx stab to pick from
4. pbt instead of abs


other than that, not much to critic, worth buying once this 2 points are done with

after install jetflo on my seidon 240M
i found out it more noise than blade master with same speed (about 1700RPM)
well it really high flow than blade master is the greatest
and the cooling seem still same about 36-42 C in idle mode (may be bcos i got some app still autorun ) no try full load so donno got how much different

so not sure need any special setup again on it bcos i cant install pull fan on it due put upper HAF X on btm can block motherboard and also cant top due different high....

thinking should i remove upper 200mm fan as pull on it or not

-------------------------------------------------------------------------------------------------------

after check again correct heat, now is 33-39 with idle mode (less than 15% load)
so far the noise still ok bcos it is better than xtraflo 120 red LED (i got try it and it is very loud until need silent mode just can same like other fan noise )
btw i am not silent build bcos HAF X more prefer for high airflow cooling especially for fan use


This post has been edited by heerosakura: Feb 24 2014, 08:53 PM

Hi noobandroid, thank you and everyone from the mechkb community for the input.
We'll take note of that for our product improvement, so keep your feedback coming!

Hi heerosakura, thanks for sharing your experience on our JetFlo and Seidon 240M with everyone here.

If you do check out my reviews, I did mention that the JetFlo is quite noisy.
http://www.tech-critter.com/2014/01/cooler...pton-140xl.html

yup i know, but need hear my self juz can know how noise is it
well for me still ok at least not noise till like engine sound

btw i forgot say my seidon 240M the radiator some fan hole lock alrdy start loss when i screw it 2nd time for change blade master to Jetflo. donno next time time if i clean the radiator want take out the fan or not can it cover on warranty? scare next time hard install fan back then got problem......

This post has been edited by heerosakura: Feb 25 2014, 02:49 PM

i think can since u din modify anything, right?
calling CM.Storm, over.

This post has been edited by lucidlts: Feb 25 2014, 03:07 PM

btw want ask normally pump speed should be how for radiator?
so far i check my 240M run on 1200 rpm for the pump, is it ok on it?

is that the speed during idle?

120mm, the 140mm is noisier but they're the darnest awesome fan that I really like.

CM should consider providing the silent profile cables as they did with the Jetflo fans for AIO WC packages.

hi CM.storm

is it possible to add backlits on my upcoming Quickfire Rapid?

I saw there's a few QFRs with backlits on CES 2014, and could my QFR be the same?