ch-5 can reach how much mhz at wat timings and wat voltages...im using a dfi expert , 7800gt , 600wt fortron and venice e6 (3000+)..can reach 280 ahh??

280MHz??? in ya dream...

i wud say 220-240ish MHz if ur lucky, timin can be as tight as 2-2-2-x, might be a 'lil bit looser thou...

beware while playin w/ these babies, they luv high voltage...

Timing set to X-2-2-2.0 and use 4.4-4.8VDimm(If u can found a mobo that supply that much ) for ur ram. Oh ya..rmb to
watercool ur ram or LN2 it . Folo what i said..280mhz should be no problem.

4.4-4.8 arr?? r u jokin' or typo??

LoL..I have a pair of Ch5..and around 3.2v ..it doing only 235mhz. Den on my friend mobo it doing 250mhz at 3.6v. So..to hit that extreme '280mhz' the ram should be run at extreme voltage and extreme cooling. Imaging ram on watercooling or LN2.

BT FOR EVERYDAY USE HOW?? voltage will kill woh...wan a stable oc that can go high...

u got few options if u wanna play low voltage module:

-tccd/5/c/4
-d43
-psc
-promos
-uccc
-etc...

depend on budget, n d capability of ya mem. ctrler oso count...

no lah i mean ch-5 can lst long ahh under high voltage?? i know it can hit very high mhz bt need carzy cooling...so around 3.2~3.5v shouldnt need carzy cooling right

no lah i mean ch-5 can lst long ahh under high voltage%3

u need active coolin when u started to feed d ram 3.0v or above... if ~22xMHz, u prolly need 2.9v +/- 0.1v.

walao wehh.. so it is 4.4~4.6V just for the RAMs. dya use DDR Booster to feed more voltage on CH-5??

hmm... like this cn ah...3.3v with allngaps ram cooler, timings 2-3-3-6...can it do 250mhz?? anyone tested??

This post has been edited by lolhalol: Jun 27 2006, 05:56 PM

I owned a pair of 256MB winbond ch5 before. pump it to 3.2v, cannot run stable 2-2-2-5 @ any frequencies even 100MHz/133MHz/166MHz, guess that's voltage regulater inside the chip resist it to run normal at high voltage. the highest and stable I tried before is 250 @ 3-4-4-8.

This post has been edited by gsan: Jun 27 2006, 11:13 PM

so with high voltage cannot this ram doesnt excel like the bh-5s ?? dat mean have to run run like 3 volts ??

That weird...since when CH5 can run under CL3.0? Perhaps ur CH5 is relabelled.

umm wat is cl3.0 mean... den wat the others mean like cl2.5 and etc...

I have no idea since I didnt take off the heatspreader, but the sticks is AK which a.k.a CH5.

is that possible that they are of hynix chippy? 3-4-4-8 @ 250MHz seems like a hynix to me... i could be wrong thou...

@ thread starter:
not naggin u, but it's always better to do sum read up b4 startin anythin that's new to u...

My UTT-CH5 also can boot CL3 ,

Prime Stable 250 @ 2-2-3-6 @ 3.2V

Pump 3.6v Vdimm also cant push hight clock speed , even loser timing same. 250 MAX.... am i noob or wat

can boot up...
but can't pass sys check...
that is what dfi so special...