See if you can get hold of Phobya or Aquacomputer pump tops. They have 2 inlets and 2 outlets.

No DDC pump has inlet/outlets at the same angle due to the design of the pump impeller and volute.

Whoaaa brooO!! Simple and clean build! I didn't know u can use the top as another connection lol. How did u fill up your loop then?
And and and~~ Your fans! Damnnn look so ganas! xD

Wanna hear another weird story, cuz of my good experience with DCP 4.0 after selling to you I bought another one! LOL.
I'm not really sure how to check the rpm but if not wrong it's flow rate was rated at 800L/Hour.


What's your temps like?


Aside of that Sentinel92 Pristine Lucassss If my cpu wb the screw are rusty how do I make it look newish? Soak in Vinegar? To be exact the screws on XSPC Intel Raystorm WB. ._."

i just go to an engineering workshop and tell them to tap a g1/4 bsp hole on the cap....filling up is cumbersome cause i have to lay the case on it's side and fill it up using either one of the 2 side ports with ketchup bottle , the fans is cheap actually but it's not meant for pc as it comes with a different header so i have to buy my own fan header and rewire it and it's really loud you will need a fan controller for it

the reason i'm asking for the rpm reading is because i want to know what is the normal speed for this pump, at full speed my pump runs at 2020++ rpm i have try googling around and couldn't find any answer...and there is this weird pulsating like sound coming from the pump, as if the pump is breathing in and out

i haven't done much testing cause busy with my kids but i'm not really impressed with load temp actually maybe it the hot weather these days. with ambient temperature 31 C i'm getting average 64C full load at 4.5 ghz. water temperature goes up to 34C after one hour... is this good guys? this is my first loop, and the reason i'm not impressed is because with my 4 year old cooler master v8 my average load temp is around 70C. while 6C drop is good but i think it's not good enough give me a few days to do some testing and i'll post some screenshot for you guys.



This post has been edited by panjangbest110: Apr 11 2014, 03:22 AM

Alright thanks !


Thanks guys for the recommendation , will check it out. My rad is white colour, so need to get a white colour fan to match it !

Lucas - chill ma bro hahaha! New loop coming soon hehehe. Really got poison much by all wc users here huhuhu.

Next update will be a ddc/d5 with cylinder res

..

haha not bad bro nice n easy loop..
but u still nyoyot tol yuyu ya...

I am chill. LOL. Wait la, when I get my radiator back then I mount my fans and he will cry.

wahhh??? at 4.5Ghz you get 64C on full load? o__O Mine even tho on stock load can reach 60C ._." Ya the water temperature is around 34C too. How do u check the pump rpm?

From the last picture I can tell you are very busy with multi tasking. Just finish feed your baby milk then take pic ya? xD

This post has been edited by gxthelord: Apr 11 2014, 12:31 PM

I mean something like the Swiftech MCP355.

Same thing. 350/355/35X/DDC. Same pump design, just different specifications. None of which have G/14" ports at the same angle. Only the 35X comes standard with G1/4" ports one on the top, one on the side, the 350/355 has stock barbs, both on the side.

In order to get G1/4" ports at the same location (either top or side), you need to change the pump top. Only pump tops that have inlet and outlet G1/4" ports on the same side is Phobya and Aquacomputer.

This post has been edited by pristine: Apr 11 2014, 02:21 PM

hahaha father still need to do his job right hehehe

ok check out this temps, today got even worse...i'm really not satisfied with this temps, this screen shot is when i use my v8


ambient temp 28c

this is just now, with my custom loop


ambient 32c, after 30 minute water temp goes up to 38c

DRRRROOOOOOOOOOOOOLZ.

perhaps i'll change my mind to get c47 fittings+acrylic tubes later..

Wahhh poisonnn

Everyone still active.. Excellent.

First time use acrylic tubing.no hard to bend it,just heat up using hairdry.

nice

fittings pkai size brapa bro? looks terribly nice...

Primochill ghost fitting ntuk rigid tubing,1/2 OD.tapi lepas tight in,scratch pulak tube.

sempoy tu..