Yes, the MUT3 device is to read the car error codes, amongst other functions....

As the alarm unit is connected to the CanBus system, technically there should be an error code if the sensor is dead (defective).... however, if the sensor is half dead, chances are there are no error code if the CanBus is able to detect the sensor at the time of the MUT3 reading (may not true technically, but it shld work this way la...)

Thus, the better way is for the technicians to sit in car and actually LISTEN if it works.... there are more simpler ways to work that to blindly rely on equipments, stupid workers....

Maybe K3 can highlight more on the MUT3..... he did COPY this knowlegde from somewhere someone ma....

duta roundabout? i stay nearby too, and the nearest proton SC is the segambut one, i service my car there and so far they haven't fail me once.

Proton Edar Segambut (Admitech Auto)
Address: 154 Jalan Segambut, Segambut, 51200 Kuala Lumpur, Federal Territory of Kuala Lumpur
Phone:03-6258 3741

maybe you can try this sc instead

I did my 1k service at Admitech. They also look at the the same issues, and they just put on the receipt "no rattle", "reverse sound ok" and "aircon outlet not loose". when i asked why they put the description like that, they say it is not always hapenning, hence it is ok to put like that. I didnt question them on this. Else i will become the next "tol car lady / listen lady". Besides, it is still a minor issue.

That is why i came to this kepong bukit maluri. According to proton, kepong bukit maluri is a proton-edar service centre and they will look into these issues i had

should be at the door.. I asked them, they still no reply.. =,=

TITAN

I not see XC's lighting anyway.. I dunno how they setup Drill hole? or ikat? lol.. I tak tau ma.. Last nite Papi Pix play around with his LED.. the controller battery almost flat edi.. so very hard change pattern.. lucky he can off it.. else sure police C, police get money

This post has been edited by ascentic: Mar 5 2013, 04:51 PM

that's weird, they replaced my loose air vents after i complained to them, and let me used my own engine oil (just once) even if that's against their protocol.

thanks a lot you guys!
You guys are the best!

Regarding the reverse sensor I rmb someone mention before.

U may have a check on the reverse sensor got a dot on it. Which suppose to point 12o'clock or 6o'clock. Later go car park I have a look again.

Anyone rmb that info? (Just some idea, might not solution)

Vincent,

Looks interesting. Can we do a GB for this orsen plate for our lala? hehehe.

Eneos got promotion,
You guys can go and check it out,

Thanks for the info. Still hope to have a group buy for this since bulk order will get better discount.

This post has been edited by k00Lric: Mar 5 2013, 08:14 PM

proton techician bestest!
our lala reverse sensor doesnt connect to can bus at all!! its a 3rd party module! and they can diagnos it with a mitsubishi tool!!! kudos

Went to Titan again today. Just my third time, to fix the bottom out issue... Erm... actually didnt went to test, not sure they test it with their crew or not (i think not, lol). They just raise the rear higher, i can put in 3 and a half fingers. Ask them what they do, the technician said higher and harder. Erm, whatever... Went back to genting, and can hear the rear sound return, faint but noticeable, last fix already reduced a lot, now increased a bit. Adui...

Orsen ka bro? Last time metoo recalled his sexperience with skid plate, ayam scared

Bro,

Did u look for wai loong or Unker Richard? Were they the 1 who advice on the raise the height?

I called Wai Loong yesterday, he said will settle for me... this morning went there, they not reach yet. I think Wai Loong trust his worker to do that? Didnt consult Richard though... Do u think there is something not right?

Going to test again tmr morning. Hopefully the sound not as loud as i hear this evening. Stress the car quite badly uphill rushing for something.

DOnt mean to be political... and also know I slowpoke..

But this one creative like heck... I laugh until peng man!

PM me for more info, there's a place selling super cheap but this promo up to month end only. 3 of us done it there already.

WTF... lol nice one, must remember to watch episode 2

G day to all,

Ong u sure u r having the bottom out issue? How do u know is it bottoming out? Raising the height will not resolve the bottom out but compresses the already soft oem spring n make matters worse..

U need the discuss with WL or Unker and not straight go to their assistants unless u know what are u doing..my humble view.

bro, i think the faint sound u noticed, probably is the tyre sound, due to suspension harder, tyre sound more obvious, not the suspension problem

This post has been edited by nzh0920: Mar 6 2013, 09:21 AM