okay... new problem..

WahroongaFarm DairymanCanada

anyone can help me with this?

it seems my MR3020 is not happy with BW.. high load..
next to it is a MR3420 running AA firmware


arif48
2 command prompt
1-> ping 192.168.1.1 -t
2-> ping 192.168.0.1 -t

boot ur router to failsafe.. sys led blinking fast for a long time.. the try all ur port on the router... see which 1 reponds..

This post has been edited by khairilyazit: Apr 16 2013, 10:00 PM

too bad.. openwrt dont support storage size more than 2 TiB..
haha

just check ur system log... maybe there's something there..

yeah.. it seems to loose stability after long hour of usage.. disconnected modem, and the high load o mentioned earlier..

maybe WahroongaFarm n DairymanCanada can take a look.. anything u need to diagnose?

i think its the same HW.. just named differently for the chinese market..

let me compile AA n trunk images again for u guys.. standard ppp connect only..

p/s: anyone need ipv6? if not i'm removing it from the package..

This post has been edited by khairilyazit: Apr 19 2013, 01:09 PM

i know.. just wanted to compile a new 1.. i think that is not RTM AA.. just RC..

meaning if ur qos is at 42000 its possible to get speed in the high 30mbps region..

ppp dialing has lots of overhead..

if u r currently using ppp n speed averaging around 4-5 mbps.. with qmi its possible to get close to 6-7 mbps..

qmi is a protocol used by new huawei zte modems..if the dashboard allows ndis connection type, it supports qmi.. i think no modem that supports HPSA+ dont have qmi support.. different companies use different naming.. sierra wireless uses usb-to-wwan if i'm not mistaken..

older modems supporting 7.2Mbps largely comes with standard RAS connection type i think..

p/s qmi is Qualcomm MSM Interface..

This post has been edited by khairilyazit: Apr 20 2013, 06:48 PM

like i said, qmi is for qualcomm chipset..

i dont know any other chipset that for usb modems..

for tablets i think nvidia uses icera for their baseband..
broadcom makes 3g radios also..

there are a lot of manufacturers for 3g chips..
so, diff companies, diff names..

there's also BALONG..
haha..
most brand is just fabricate.. design mostly ip licenses bought and modified to meet companies target..

its already set for u by the OpenWrt rite?
thats the purpose of Dairyman's ROOter project...

see ur IPv4 WAN connection type.. if its wwan then its already using qmi..

*applicable to supported modems only..

Ok guys.. i compiled a normal version of OpenWrt.
Both the Attitude Adjustment 12.09 and Barrier Breaker based on the r36349 source.
both images include needed package to run 3g modems using ppp.

MAKE SURE TO CHANGE THE MODEM DEVICE ON THE 3G-WAN INTERFACE PAGE TO YOUR PROPER DEVICE

PLEASE COMPARE THE MD5 HASH OF THE DOWNLOADED FILES WITH PROVIDED md5sums TO MAKE SURE YOUR DOWNLOADED BIN FILES IS NOT CORRUPTED

Attitude Adjustment 12.09


Barrier Breaker r36349

as i only have MR3420 and MR3020, i can only test on these two devices.. please give feedback for other models.. i didn't compile images for V2 router as i dont know if it is supported directly or if patches is needed in trunk..

ZTE MF680 is also experiencing this..

or is it limited to our telco?

as it seems to coincide with the kick-out period of our telco..

why dont u ask for 1 during the AA days.. its still the same architecture... from the same build image.. hehe

guys if u want the new theme for ur router.. try searching for luci-theme-bootstrap at the software tab..
if got install then set it at the system tab, language part..

Do any of u guys notice the wifi is limited to 72.2mbps only.. 20mhz stream.. i cant seem to bump it to 40mhz..

chuahcs79

refer to my post some time back.. i uploaded n compiled AA for all tplink MR routers..

where in kk are u?
i'm getting good speed in papar here..
ping could be better though... avg 100ms here...