haha ya. i plan to holesaw 2 120mm hole. but some grills and place some filter.

It'll be better if you can find someone to laser cut for you, cleaner cutting

hmm l;aser cut sound expensive. where can i even get that service?

not sure about the pricing, but here's your place to go:
http://www.lasercut.com.my/index.php

a small cut won't cost you Rm100 i think?
can try to ask them the pricing maybe.

This post has been edited by lucidlts: Dec 5 2013, 05:54 PM

hmm cause mine old casing. i dun wan to spent so much. haha

simply and cheap will do for me.

well, you can ask the price 1st, if it's okay then you can consider to go for it.
unless you're an expert in cutting metal stuffs, I tried to cut my old ayam case once, never again i will do it again.

omg what happen?? sumtin i should be prepared? hahaha.

Ok so I swapped the fans and did some cleanup of my cables... and in my excitement forgot to take "before" measurements

I compared the difference between running fan at 800rpm and 1400rpm, at 40% GPU load. The GPU temp lowered from 59C to 56C, and GPU fan lowered from 1800rpm to 1600rpm.

I also learned that the Gigabyte mobo I have is terrible for controlling PWM fans, so I resorted to using SpeedFan.

that's quite an improvement actually, maybe not so much on temps but noise levels must be down quite a lot already I think? at 1400rpm the F12 should be fairly quiet

Well, i got uneven cut as result. The thing you should be prepared which i personally think is some skills

haha well thats normal. so far my temps is okay. just tempted to make a hole

Where can find this SilverStone SST-AP123 case fan? Cause i want use it as intake on front of my pc case which can direct blow to my display card... or any sifu can recommend me the fan such like AP123?

I was looking for this model since few months ago, seems MY distributor havent't bring in yet.

mean we can't get this SilverStone AP123 case fan in malaysia... MY distributor faster bring in it!

Ask Edifier...

Halo Sifu! Does any fan like SilverStone AP123 can recommend? Don't want wait MY SilverStone distributor bring in anymore, other country already released long time ago, but malaysia still no any news at all!

Hi Expert Bros!

I've just bought a CM HAF XB casing (completely fell in love with it) and installed Maximus 6 Hero, 4670k i5, Asus R9 280x DCU II GPU...

It's my first time DIY and self taught from YouTube videos and reading magazines. What I need to understand is have anyone here moderately mod this casing and successfully made an absolute cooling setup.

Currently I'm using Seidon 240 with 2xPush Gentle Typhoon 120mm with rear casing stock Seidon fans (since its there so just bolt on and use) ...2x Noctua RF 8 80mm silent casing fans for under carriage exhaust.

Core temp at 34 c but 26c with air con condition
Mobo temp at 30c but 22c with air con

Are these good temps? I only could fit one side of the seidon as push pull configuration as the other side...well the Asus R9 280x is too long to fit another pull.

So i was fulling around with it by installing a Noctua NF-F14 140mm to see if I could boost the CFM that is written on the box is 115.2

What I'm trying to figure out is ...am I doing the right thing? Oh...The top cover is the window type not the mesh with 200mm fan type.

Pls help!

Saw it in Viewnet sometime back, but they haven't brought back the AP series since it ran out of stock... maybe getting from ebay?

Temps seems normal to me, no cause to worry, so long as you have air movement flowing in from one direction and complement the exhaust in the same direction your fan setup is just fine regardless of how many exhaust you have as that's the most optimal... unless you mod the chassis

adding a high CFM fan will help in a way but don't expect much drop from the temps

any1 got try cooler master jetflo?
the price look not bad and i thinking should use it for the liquid cooler

Noctua still considered as the best fan for desktops?

I feel like my fans barely do the job