refer klseet website ....

http://klseet.com/index.php/tl-wr1043nd-ve...unifi-10031-rc6

or

http://www.klseet.com/index.php/rt-n10-c1/...openwrt-a-unifi

Thank you.

This post has been edited by kaisam: May 15 2013, 01:44 AM

set it to a little lower speed than your subscribed internet package.
you can test download and upload speed at speedtest.net
take note,the unit in speedtest.net is mbps.

you can do a little more reading at here.

BTW, does anyone of you managed to revert back to stock firmware from OPENWRT?
I just couldn't do it.
It failed at image file validation. It gave error, "Image is not correct" something like that.
I never able to get to this page.

Picture snipped from Klseet site.

I have tried 3 times.
1st, when I was using tplink 1043nd v1.8 with backfire 10.03.1 = failed, i forced from ssh, then I bricked it. Send for warranty claim.

2nd, i got back my router, installed altitude adjustment 12.09 beta, try to revert = failed, i forced from ssh, I bricked it again. Send for warranty claim.

3rd, just got my router back a week ago. They gave me a new one v1.10. Installed altitude adjustment 12.09 latest, revert = failed. This time, I don't dare to forced revert from ssh anymore.
Well, I just want to try to revert for the sake of knowledge.
I have bought a usb-ttl just in case I might brick it again.

Any inputs guys where did i do wrong?
Just for information, I downgraded my stock tplink firmware to german firmware.
Then, i installed OpenWRT.
When I want to revert, I downloaded tplink firmware that only contains the word "up" in the filename.

Picture snipped from Klseet site.

normally revert back to stock firmware is very simple get the correct stock firmware without "boot" in the file name then goto backup/flash firmware page flash with patiently until the tplink came up or after long wait if tplink configuration page not come out try to refresh web page do not restart the router. i bricked it two times both were in same fault my advice is must wait until tplink configuration page come out.

thanks for your reply. do u flash it via interface or commandline?

the thing is, when i upload the image file, it always said wrong image file/ image file is incorrect.
i will upload the picture after work so that you guys are more clear with what i'm trying to say.

As for klseet using the openwrt firmware, how we going to use the ddwrt as same setting as this? I try the klseet ddwrt setting before, not working for me.

i flash it via interface

here the link for unifi stock firmware https://disk.yandex.com/public/?hash=%2Bz3o...gE5s9j/z3mhc%3D

This post has been edited by mrchloo: May 20 2013, 08:54 PM

Got this error message by using the image file above.

-------------------------------------------------------------------------------------------------------------
-Edited-

Revert via ssh. Solved.

This post has been edited by mastermindsos: Jul 9 2013, 03:27 PM

hi sifu,

may i know the best mtu value?

1492 or 1500?



Attached thumbnail(s)

Wow I did not know about this. Very interesting. Might give this a try when i go home.

mtu

I tried this yesterday. With both MTU values set in WAN, i can still ping google without any packet loss.
But, by using the command,

ping -f -l 1472 www.google.com --->1472+28 = 1500, this one fails.
ping -f -l 1464 www.google.com --->1464+28 = 1492, success (1465 and above fail).

Why I can still ping www.google.com when I used mtu 1500, but with this command ping -f -l 1472 www.google.com it failed? Aren't they the same thing?

This post has been edited by mastermindsos: Jun 5 2013, 02:33 PM

Thank you for the great tutorial, my router is now BRICKED. I bet countless people trusted this guide....

Are you trying to blame the threadstarter for his guide?