You can try pming bloomker or see his website.

You might also want to get filaments for your printer and I would recommend quality filaments from Qwikfab. Try not to buy filaments from aliexpress or china sourced filaments because there have been cases of poor quality filament messing up prints and damaging the 3D printer.

I am still in the midst of discussing with Qwikfab in bringing 6+ spools of Q-PLA. You can combine your shipping with me if you like.

Also, check out my siggy below if you need to get the Prusa I3 parts printed.

Hi, can anyone tell me how is the quality of the Reprap Prusa i3? I'm planing to buy one. Please also suggest the brand of 3d printer that is worth.

If I was to rebuilding my 3d printer all over, this is my advice:

1. I'll choose P3steel http://reprap.org/wiki/P3Steel . With the current steel price, you can laser cut for around rm200. That cover most of the body.
2. Get professional to spray paint the steel body.
3. Get all electronic parts as a complete set. It's save a lot of trouble and money in hunting down small part.

http://reprap.org/wiki/RUG/Malaysia

Supreme Steelmakers Sdn Bhd (laser cutting)
No 8, Jalan Tiga Off Jalan Sungai Besi, 55200 Kuala Lumpur, Wilayah Persekutuan.
+603-9223 6666
sales@ssmsb.com.my
http://www.ssmsb.com.my
P3steel cutting service and 3mm steel cost = rm250(email quoted on jan 2014),rm200(walk in around June 2015).
U can see how much steel price have drop. Bring .dxf file with u.

Additional advice.
1. Bearings in Malaysia is very expensive especially those small bearing.its cheaper to get from china and replace as they wear.
2. Screw and nuts.Shops that I visit call Hex screw as capped screw. There's 3 type of screw and nuts. Steel(refer to black) which will rust. Galvanised steel(white) will not rust but not available for all size/length. Stainless steel have all size,but some size can be very expensive like m3 50mm is double the price of m3 40mm.

Nice... but i just ordered 1 from element14. Thanks.
You can get electronic from china, check review before purchase eg. http://www.aliexpress.com/store/group/3d-P..._257509064.html

i don't understand why you need lead screw. http://reprap.org/wiki/P3Steel_Vitamins

Can tumpang shipping with you? I could buy a few lead screws with nut from you... I don't know how to read taobao but can get the largest threaded rods with nuts each.

http://reprap.org/wiki/RUG/Malaysia

Supreme Steelmakers Sdn Bhd (laser cutting)
No 8, Jalan Tiga Off Jalan Sungai Besi, 55200 Kuala Lumpur, Wilayah Persekutuan.
+603-9223 6666
sales@ssmsb.com.my
http://www.ssmsb.com.my
P3steel cutting service and 3mm steel cost = rm250(email quoted on jan 2014),rm200(walk in around June 2015).
U can see how much steel price have drop. Bring .dxf file with u.

Additional advice.
1. Bearings in Malaysia is very expensive especially those small bearing.its cheaper to get from china and replace as they wear.
2. Screw and nuts.Shops that I visit call Hex screw as capped screw. There's 3 type of screw and nuts. Steel(refer to black) which will rust. Galvanised steel(white) will not rust but not available for all size/length. Stainless steel have all size,but some size can be very expensive like m3 50mm is double the price of m3 40mm.

Regardless which method,they still need you to pay first.You can try your luck by walking in and ask for a quote. If it's more expensive,bring up the email quote.if lesser,just shut up.

And u can try to say last time your friend did the same design for rm200++. See what they say.

It take 1 or 2 working days to ready.

How much is it?

Is there a supplier for Xtc-3D locally ?
http://www.smooth-on.com/Epoxy-Coatings-XT...1429/index.html