[Official] LYN DDR3 Discussion Thread, Show or Learn To Overclock Your DDR3!!
|
|
 Sep 3 2012, 07:35 PM
Return to original view | Post
#21
|
 
Senior Member
1,162 posts Joined: Oct 2007 From: 8.8.4.4   
|
QUOTE(saturn85 @ Sep 3 2012, 07:18 PM) » Click to show Spoiler - click again to hide... «   but hope to see this module at higher rated speed  This post has been edited by lengchai86: Sep 3 2012, 07:37 PM |
|
|
|
|
|
Sep 4 2012, 10:51 PM
Return to original view | Post
#22
|
|
Senior Member
1,162 posts Joined: Oct 2007 From: 8.8.4.4
|
QUOTE(stasio @ Sep 4 2012, 12:35 PM) ^Kingston use hynix CFR chips....not so god. all KHX using hynix CFR chip?  http://www.ocaholic.ch/xoops/html/modules/...emid=801&page=1  |
|
|
Oct 25 2012, 02:39 PM
Return to original view | Post
#23
|
|
Senior Member
1,162 posts Joined: Oct 2007 From: 8.8.4.4
|
QUOTE(keyo @ Oct 25 2012, 02:11 PM) izzit 1.65v to high stock voltage only 1.5 1.65V is very safe <-- as told by my sifu dato' Kuntawakaweven some otai here running 1.8-1.85vdimm during benching and most review here in LYN running bench at 1.7-1.75V but of course not recommended for 24/7 setup one of my favorite reviewer, Sir ah_khoo xtune review and ballistix tactical |
|
|
Nov 8 2012, 11:19 PM
Return to original view | Post
#24
|
|
Senior Member
1,162 posts Joined: Oct 2007 From: 8.8.4.4
|
Apacer ARES 2000 (2GbX2) 9-10-9-27 2T (1.65V)
 Chip : Hynix BFR  1600 6-8-7 1T @1.675Vdimm. 1.65V BSOD 1.66V cannot pass hyperpi8M currently tested on AMD 960T Phenom II sorry no prime95 test   This post has been edited by lengchai86: Nov 8 2012, 11:20 PM |
|
|
Nov 9 2012, 02:07 AM
Return to original view | Post
#25
|
|
Senior Member
1,162 posts Joined: Oct 2007 From: 8.8.4.4
|
2500 10-13-12 1T 1.685Vdimm
 |
|
|
Nov 12 2012, 08:16 PM
Return to original view | Post
#26
|
|
Senior Member
1,162 posts Joined: Oct 2007 From: 8.8.4.4
|
QUOTE(keyo @ Nov 12 2012, 05:08 PM) can i ask all epilda chip good for oc or not i see kingston value 8gb 1600 using epilda chip is it good for oc only certain elpida (BFSE, BBSE, hyper) is good. i have tried BDBG (single sided) and BFBG, both not good at all most good chip is on the 2gb stick, i don't think 8gb stick have such a good chip btw you can try OC them and post result here for our reference |
|
|
|
|
|
Jan 6 2013, 01:03 PM
Return to original view | Post
#27
|
|
Senior Member
1,162 posts Joined: Oct 2007 From: 8.8.4.4
|
QUOTE(keyo @ Jan 5 2013, 02:15 PM) nak tanya otai ram ni best tak oc how about you try OC them then share the result here  i personally never tried any qimonda chip before. |
|
|
Jan 11 2013, 10:04 PM
Return to original view | Post
#28
|
|
Senior Member
1,162 posts Joined: Oct 2007 From: 8.8.4.4
|
QUOTE(keyo @ Jan 9 2013, 11:46 PM) buy this ram rm 50 d9kpt ,can i know how far this ram can go,is it ok not using heat sprader using voltage 1.6v tq some info regarding this chipQUOTE average D9KPT/KPV clocks same as handpicked D9JNL/JNM 1600 7-7-7 : 1.70-1.75V for KPT , 1.75-1.80V for JNL 1800 7-7-7 : 1.85-1.90V for KPT , 1.90-2.00V for JNL 1800 8-8-8 : 1.70-1.75V for KPT , 1.75-1.80V for JNL 2000 8-8-8 : 1.90 for KPT , 1.95-2.00V for JNL 2000 9-9-9 : 1.70-1.75V for KPT , 1.85V for JNL link : D9KPT @OCXtreme.org btw you can go up to 1.65V which is very safe. for benching, some people dare to go up to 1.9V (if the chip didn't give up yet) but for me, 1.8V is my redline --> depends on voltage scaling for the chip. This post has been edited by lengchai86: Jan 11 2013, 10:06 PM |
|
|
Jan 13 2013, 11:10 PM
Return to original view | Post
#29
|
|
Senior Member
1,162 posts Joined: Oct 2007 From: 8.8.4.4
|
QUOTE(t3n @ Jan 13 2013, 07:17 PM) Micron D9PFJ more PFJ HERE Thanks bro..!! This post has been edited by lengchai86: Jan 14 2013, 02:57 PM |
| Change to: |  0.0271sec
 0.45
 7 queries
 GZIP Disabled
Time is now: 1st December 2025 - 02:35 AM |
Quote