Welcome Guest ( Log In | Register )

Bump Topic Topic Closed RSS Feed
34 Pages  1 2 3 > » Bottom

Outline · [ Standard ] · Linear+

 -+♦+- LYN PROTON PERSONA CLUB V15 in 2011 -+♦+-

views
     
TSxandras
post Apr 17 2011, 01:33 AM, updated 15y ago

Getting Started
**
Junior Member
52 posts

Joined: Dec 2010



LYN Official Proton Persona Owners Club and support thread V15

PPLYNC

Persona celebrating one dozen +3 threads of awesomeness!!

user posted image

IMPORTANT ANNOUNCEMENT!!


TO ALL FELLOW PPLYNC MEMBERS WHO ARE DRIVING PERSONA ELEGANCE:

If you have ever experienced sounds (tak tak tak tak tak) coming from your engine during cold start in the morning, then it MAY BE one of the infamous Proton's manufacturing defect: the IAFM problem. IAFM noise is most noticeable during cold start, and you may hear the frequency of the noise going up or down depending on the RPM that the engine is running at. The noise is identical to a diesel truck or lorry's engine idling noise. Once the engine has warmed up, the noise will become softer or totally eliminated. This is because the plastic components on one of the valves on IAFM expands with heat.

So far the problems that may be associated with IAFM noise are nothing major, but in certain cases it may cause severe throttle lag, and the noise may get louder over time. Some owners have even experienced increase in fuel consumption and bad engine response.

If you visit the service centre and the mechanic or service attendant tells you that the noise is not caused by IAFM as our Persona Elegance comes with new batch of IAFM modules, DO NOT believe what they said.

You may:
1.) Ask them to diagnose and tell you what exactly is the problem since they insisted that it's not IAFM module noise.
2.) If the mechanics at CoSE tell you that the noise is not caused by IAFM, go to a few different SCs, have them to check your IAFM module for imperfections on the valve, then get them to write a report each. Compile these reports & bring it to CoSE's customer service and file a complaint, give it to their higher authority.

Now, do remember that they may not be able to figure the noise out if you send your car to SC as the engine has already warmed up. Park your car and leave it there for an hour or so for the engine to cool down, then get the service attendant or mechanic to listen to the noise as you start the engine.

Again, I would like to stress on this main point as I've experienced this myself and wasted almost a month plus before sending it to a different SC just to have the noise diagnosed as IAFM problem; If the guys at CoSE tells you that it's not IAFM problem but your guts and 13 other SCs tell u that it is, then it IS IAFM problem. In my case they never even bothered to check as the engine has already warmed up and the sound was gone by the time the mechanic laid his hands on my car.

This serves as an important announcement to all Persona Elegance (PE) owners as to not overlook this small issue that may lead to greater problems in the future. The price of IAFM modules has dropped since year 2009 (from RM 1200+ in late 2008 to RM 2xx in 2011) because of the frequency of Campro IAFM engines having this problem. Still, it's our right to claim the IAFM modules as they are covered under warranty and malfunctioned units are manufacturing defects. We should not wait till the warranty period is over and then pay them RM300+ including labour to fix a defect that is there from day 1 of ownership of the car itself.

I hope all the Persona Elegance owners out there take note of this issue and do not keep an eye closed.

Salam 1 Malaysia, & Harap Maklum.

BULK ORDER V4
Dyno chart y u shd get Denso instead of other brands. Lesser misfires and higher power gain.
DYNO CHART
Price RM160/set of 4. Includes postage.
Each plugs can last 100,000 KM lifespan compared to OEM NGK only 20k KM.
DENSO IRIDIUM 0.4mm Spark Plugs
Please PM me to join the bulk.

1) tepungtalam
2) selangorclay
3) samwongjyhhorng
4) saiful_azhar
5) vccy
6) pupumaru
7) fenrir0402
8) saddient

2 more seat left!!


BULK ORDER V5

Rapid Stop 550'C Brake Pads. Front only, RM 130. For H-Line owners with rear disc brakes, if you want the rear brake pads as well I'll have to ask for a different quotation from the dealer. For now the bulk is for front brake pads only.

user posted image

Pros of RS:
1. Higher working temp.
2. Doesn't need to warm up first every time u start ur car to provide immense braking power.
3. Less fading, lasts longer.
4. Less brake dust than OEM pads.
5. Price.

Cons of RS:
1. Needs bedding in.
2. Not so well known like MKT.
3. Can be spongy if not bed in correctly.

If possible, a TT will be held where buyers will be given their brake pads and will be taught on how to bed in the brake pads accordingly & evenly.

RM 130 only, need at least 10 members here to get bulk price. Might be able to get cheaper if more people join the bulk.

1. ZengTMM
2. K.Lee
3. onijoseph
4. RokXIII
5. pupumaru
6. fenrir0402
7. selangorclay
8. MjMax15



Photos From Recent TTs
TT 4.0 - Genting Highlands.
» Click to show Spoiler - click again to hide... «



Studio shots of the New Persona Elegance (PE)
» Click to show Spoiler - click again to hide... «


Proton Persona Promotional Video
» Click to show Spoiler - click again to hide... «


Previous Threads V1-V14
» Click to show Spoiler - click again to hide... «


Proudly a Proton Persona Owner
» Click to show Spoiler - click again to hide... «


215 Members and Growing!!! Mega TT will be fun if all 215 Members show up!!

For those who just received their Persona, Congratulations & Welcome to PPLYNC!! Please PM ME or POST in this thread stating that u are a new owner to update you name into the list.


Car Service & Preventive Maintenance Schedule and Pricing
» Click to show Spoiler - click again to hide... «


Price of Proton Parts
Proton Parts Cost

Recommended SC

1)Serdang SC - http://worldcarcare.com.my/WorldCarCare.html
Reasons: Best customer service in all reviews, allows you to bring own lube.

2) CoSE (beside Kesas) - Head towards Klang on Kesas and you will pass by the biggest Proton billboard you'll ever see. Thats the place.
Proton Center of Excellence (CoSE),
Jalan TP 5, Taman Perindustrian Sime Uep, 47600 Subang Jaya, Selangor, Malaysia
+60 3-8026 9999 ‎
HQ, easy to claim warranty and reflash ECU. Have to make appointment b4 going there. Can bring own Lube

3) Juru SC (Penang) - Can bring own lube.

4) Trend point - Along Jalan Tun Razak. (Still under review, first review was bad, but a warranty claim experience after that shows that they're quite efficient and able to detect problems that even CoSE denies.)

Unrecommended SC (TRY TO AVOID AT ALL COST!)

1) Sin Siang Hin sdn. bhd. at genting klang n gombak - bad service and they whack ur car like they pay for petrol

Common Problem in Persona
» Click to show Spoiler - click again to hide... «


Tips for Persona Users (To be Updated)
» Click to show Spoiler - click again to hide... «


Jokes and Funny Remarks Made By PPLYNC Members
» Click to show Spoiler - click again to hide... «


This post has been edited by xandras: Apr 26 2011, 06:26 PM
TSxandras
post Apr 17 2011, 01:37 AM

Getting Started
**
Junior Member
52 posts

Joined: Dec 2010



If not? Because of spammers like u all lah.. brows.gif
TSxandras
post Apr 17 2011, 01:40 AM

Getting Started
**
Junior Member
52 posts

Joined: Dec 2010



Btw KKW...
Triton 175HP 400 NM

TSxandras
post Apr 17 2011, 01:44 AM

Getting Started
**
Junior Member
52 posts

Joined: Dec 2010



QUOTE(saddient @ Apr 17 2011, 01:39 AM)
no reserved?
*
Nope.. Everything will be updated in 1st post d..

QUOTE(KKW @ Apr 17 2011, 01:39 AM)
Where is zeng?
*
Here's the funny thing..

Our original TS seems to always get caught with indecency.. Last time he got banned for posting inappropriate stuffs.. This time he's at Zouk groping/dry-humping/ possibly got gang-banged by a bunch of hot ladies..

Haiz.. whatever happened to our original TS....? brows.gif
TSxandras
post Apr 17 2011, 01:46 AM

Getting Started
**
Junior Member
52 posts

Joined: Dec 2010



QUOTE(vexus @ Apr 17 2011, 01:42 AM)
i saw the new batch persona scale down the sound insulation material. There is no bituminous layer at the rear tyre fender. Please take a peep.
*
Really? Any pictures to prove ur findings? Please do upload them and share it with us, u will be cited as the original source of the pictures and be credited. rclxub.gif Did too much referencing work, excuse me. laugh.gif
TSxandras
post Apr 17 2011, 01:49 AM

Getting Started
**
Junior Member
52 posts

Joined: Dec 2010



Hmmm... Our previous thread lasted approximately 15 days.

2500 posts divided by 15 days = 166.66666667 ~ 167 posts a day.

Gila la u all.. rclxub.gif But I think it may be caused by all the hype about Genting TT and such.
TSxandras
post Apr 17 2011, 01:53 AM

Getting Started
**
Junior Member
52 posts

Joined: Dec 2010



QUOTE(vexus @ Apr 17 2011, 01:49 AM)
saw it at mines showroom
*
I see. Did u checked the door panels as well? The door and pillar panels are quite heavily insulated as well. U will be able to hear the difference by lightly tapping the panels on the new models and comparing it to the previous batch.

Perhaps it's just a case of careless mistake by the factory workers for not covering the fenders with bitumen layer? Is this only seen on the display car or on other cars as well?
TSxandras
post Apr 17 2011, 01:55 AM

Getting Started
**
Junior Member
52 posts

Joined: Dec 2010



QUOTE(arfaie @ Apr 17 2011, 01:52 AM)
here is mine..i noticed it since last month

*not my car, its one of our member club

[attachmentid=2160495]
*
I see. Nice finding. Will share it soon on 1st post.

QUOTE(vexus @ Apr 17 2011, 01:52 AM)
u never sleep early. You do not have 8hr sleeping. Kidney resting time start around 10 to 11pm.
*
laugh.gif Master of sleeping speaking.


Added on April 17, 2011, 1:59 am
QUOTE(K.Lee @ Apr 17 2011, 01:55 AM)
you guys better check my car the next tt..
*
Take a picture of it & upload it here.

QUOTE(arfaie @ Apr 17 2011, 01:55 AM)
already seen some latest batch elegance, it didnt come with that layer already
*
Really? Which batch is ur friend's PE?

QUOTE(vexus @ Apr 17 2011, 01:55 AM)
2 car parking over there also same issue. Maybe computer error? or Proton trying to cut cost follow NAZA style?
*
I shall investigate this matter and refer it to CoSE for explanations. It is humiliating if Proton is really trying to cut cost as the insulations are one of PE's plus points.

This post has been edited by xandras: Apr 17 2011, 02:03 AM
TSxandras
post Apr 17 2011, 02:05 AM

Getting Started
**
Junior Member
52 posts

Joined: Dec 2010



QUOTE(K.Lee @ Apr 17 2011, 02:04 AM)
Those are the stuff that keep the nvh low, right?
*
Yes. It's one of the main reasons why some ppl actually claimed that PE's NVH is better than City and Vios, thus making it a selling point.
TSxandras
post Apr 17 2011, 02:12 AM

Getting Started
**
Junior Member
52 posts

Joined: Dec 2010



QUOTE(K.Lee @ Apr 17 2011, 02:10 AM)
it does better than vios, but i'm not sure my current drive is equal as the badge b4 mine. I did test drive when it 1st launch and the nvh was really good. Will upload photo 2moro! bad proton... if really don't have then how? can fucuk proton up side down or not?

the elegance already cost more, yet they reduced what it is suppose to be in the car! vmad.gif
*
I think it's missing on this year's batch. Will check mine too as reference. And if it's missing, we can actually file a complaint & demand explanations from them as to why they reduce materials in the process of making our cars.
TSxandras
post Apr 17 2011, 12:10 PM

Getting Started
**
Junior Member
52 posts

Joined: Dec 2010



QUOTE(K.Lee @ Apr 17 2011, 10:58 AM)
If not because of my pocket, i already ended up with the MT fiesta...  brows.gif the gear shift is fast, pick up also fast, see the red rpm needle & km/h needle...  brows.gif  drool.gif
fast and smooth car... it's 140 like still driving at 40-60... the NVH really superb compared to other same price range car... am still drooling over one every time i see one..
*
Woi. No need sleep ka u?


Added on April 17, 2011, 12:13 pmMaybe we can go for Honda insight's original aluminum rims for performance.. Rims + tyres only 15 kgs laugh.gif

This post has been edited by xandras: Apr 17 2011, 12:13 PM
TSxandras
post Apr 17 2011, 04:15 PM

Getting Started
**
Junior Member
52 posts

Joined: Dec 2010



QUOTE(~ATI4LIFE~ @ Apr 17 2011, 01:32 PM)
HEY...BTW WHOS PERSONA IS THE GREY ONE IN THE PIC....LUKS RELI COOL.....NICEEEE...R3 RIMS..AND HIS MUFFLER LUKS GUD
*
LoL.. I appreciate and am flattered by ur comments.. But no need caps lock everything to show me ur excitement lah..laugh.gif


Added on April 17, 2011, 4:17 pm
QUOTE(KKW @ Apr 17 2011, 03:55 PM)
I just send my car to wash  smile.gif
[attachmentid=2161280]
*
Nice.... Shiny shiny black laugh.gif

This post has been edited by xandras: Apr 17 2011, 04:17 PM
TSxandras
post Apr 17 2011, 04:19 PM

Getting Started
**
Junior Member
52 posts

Joined: Dec 2010



QUOTE(saddient @ Apr 17 2011, 02:52 PM)
the genting TT pic..... lol xan see so many ppl like ur car d... becareful might got stolen soon by lyn forumers hehhehe only rims and exhaust lol....
*
Lols... First n main suspect u lah.. laugh.gif

QUOTE(forbidden84 @ Apr 17 2011, 03:56 PM)
any 1 know what type and brand of brake oil is PE using? thanks..
*
Proton car using proton brand lah..laugh.gif should be dot III if I'm not mistaken. Sorry, but brake oil is not my area of expertise blush.gif


Added on April 17, 2011, 4:21 pm
QUOTE(samwongjyhhorng @ Apr 17 2011, 04:18 PM)
juz come bec from exhaust shop..was install 2 straight bullet and s flow muffler...i din noticed wat is d difference but i can noticed is the bass sound from muffler quite nice,but quite loud for me cry.gifa bit like ah beng car lo blink.gif  the sound onli appear at 2.5k - 3.5rpm when rev..when go smooth at 90 or 120,the sound juz can hear little bit bass sound onli..pick up time quite loud lo...i think need change to others muffler on next few month cry.gif i afraid lose top speed wit tis setting,so i juz test at lekas highway..wit press 3/4 pedal,my car can easily to automatically drag wit 3rd gear until 170 then juz change gear...i was hit to 180 and i release pedal ady..i tested wit aircond on condition..the FC oso not much difference..is same as my stock condition..
*
Haha... Good good..

This post has been edited by xandras: Apr 17 2011, 04:21 PM
TSxandras
post Apr 17 2011, 04:38 PM

Getting Started
**
Junior Member
52 posts

Joined: Dec 2010



QUOTE(ZenGTMM @ Apr 17 2011, 04:35 PM)
LOL.. Impossible lah.. Mde of magnesium alloy also cant be that light.. Its 1tire and 1 rim 15kg.. Like our alloy PE.
That one our TS one loh..  thumbup.gif
saddient u secretly targetting it in ur heart ady lah.. hehe..,
The Proton own OEM brand loh.. Not sure what brand. But for grade its DOT 3..
Wasai u... u... u......... Never call me go.... FFK me....
*
Zeng woke up d? brows.gif
TSxandras
post Apr 17 2011, 04:44 PM

Getting Started
**
Junior Member
52 posts

Joined: Dec 2010



BMW X6 M OEM 20 Inch rim + tyres = 40 kgs EACH brows.gif
TSxandras
post Apr 17 2011, 05:07 PM

Getting Started
**
Junior Member
52 posts

Joined: Dec 2010



QUOTE(ZenGTMM @ Apr 17 2011, 04:55 PM)
Ya loh.. haiz.. Still so tired.. No energy..
Oic.. Ok fast fast join for TT tmr.. I want to test test.. See the sound quality how.
45kg leh..  thumbup.gif
*
45 ka?? Super heavy lo.. I think the whp loss caused by the rims also more than our engine's output d..laugh.gif


Added on April 17, 2011, 5:08 pm Tired?? I Jz came back from cheonging leh brows.gif

This post has been edited by xandras: Apr 17 2011, 05:08 PM
TSxandras
post Apr 17 2011, 05:16 PM

Getting Started
**
Junior Member
52 posts

Joined: Dec 2010



QUOTE(KKW @ Apr 17 2011, 05:13 PM)
Yup. I manage to remove my water mark on my windscreen..
I ask them help me to polish it..  rclxms.gif
*
Got ask them to put rainax? I think I wan buy 1 bottle soon d..
TSxandras
post Apr 17 2011, 05:22 PM

Getting Started
**
Junior Member
52 posts

Joined: Dec 2010



QUOTE(samwongjyhhorng @ Apr 17 2011, 05:20 PM)
kepong..


Added on April 17, 2011, 5:21 pm

how to upload video?teach me
*
So how? U satisfied with ur exhaust? Btw what kind of bullet they used n what's the length?


Added on April 17, 2011, 5:22 pmUpload to YouTube then paste here lo..

This post has been edited by xandras: Apr 17 2011, 05:22 PM
TSxandras
post Apr 17 2011, 05:27 PM

Getting Started
**
Junior Member
52 posts

Joined: Dec 2010



QUOTE(KKW @ Apr 17 2011, 05:24 PM)
They use their own solution..
If u want use rain-x pls dont use on windscreen because it will spoil the wiper..
*
Spoil wiper like how?
TSxandras
post Apr 17 2011, 05:29 PM

Getting Started
**
Junior Member
52 posts

Joined: Dec 2010



QUOTE(samwongjyhhorng @ Apr 17 2011, 05:23 PM)
not so nice for me..quite loud at 2.5k to 3.5k rpm..if rev after 4k then langsung no sound lo..weird..


Added on April 17, 2011, 5:24 pm

ok..i will try and uploas on tonite..hehe..both is straight flow..ya,the powerzone people din do well welding and cost a bit leaking between  extractor and nenas vmad.gif ..but the fellow who help me install bullet ady help me cut it and re-weld bec without charge..
*
I know, but what kind of straight flow n what material? Plus, is it layered with fibre inside? And what's the length? U go top speed no sakit kepala meh with the noise? rclxub.gif

34 Pages  1 2 3 > » Top
Topic ClosedOptions
 

Change to:
| Lo-Fi Version
0.0440sec    0.47    7 queries    GZIP Disabled
Time is now: 30th November 2025 - 06:43 PM