i'm not understand bout baseband..i buy this phone already in 2.1 version..i use 6.1.3 version by wolfbreak...i have finish 2.21 but no signal

Here's the simple how to get to stock firmware :-

1. Download Sony Ericsson Update Service (SEUS) application from here http://www.sonyericsson.com/cws/support/so...x10?cc=gb&lc=en and install it into your pc.

2. After the installation has finished, run the application and just follow the onscreen instructions. If this is the first time you are doing it, it'll take some time as SEUS will download around 120MB of firmware data to your PC before it can flash to your phone.

3. You'll be back to stock firmware now

---

Added on May 17, 2011, 1:22 amGo to Settings -> About phone, there you can see your baseband version. Normally it will state there 2.0.xx, xx is the version of your default baseband.

This post has been edited by tot31: May 17 2011, 01:22 AM

oh,need to install baseband before flash the phone??

---

Added on May 17, 2011, 1:25 ammy baseband version is 2.1.54..

This post has been edited by fiz_elmo: May 17 2011, 01:25 AM

i m currectly using widgetlocker to customize my lockscreen
u guy should hav a try...=D

I suggest redo the whole procedure again.

my phone is 2.1.54 too...it work perfectly on WB's rom 6.1.3!

This post has been edited by amon90: May 17 2011, 01:31 AM

in progress...downloading software..mayb i miss to choose baseband..thanks tot31..i will start again..

No, you don't need to...ok like this...Wolfbreak rom is meant for baseband 2.0.54 and above, so if your default baseband is 2.0.54 or 2.0.55 or 2.0.58, you are ready to go.

So if you're on bb54 then it's a straight forward procedure...always start with a fresh install of stock firmware. In your case I suspected that you have flashed the cm6bb49.zip patch file which you don't need to....My advice, if this is the first time you're trying to install custom rom, stick to the stock kernel, once you have more knowledge then go to the next level by using custom kernel..



This post has been edited by tot31: May 17 2011, 01:36 AM

i need do seus right??then need to flash?

wat is kernel and bb difference?
android beginner here ><

These steps apply to default baseband 54 on How to Install Wolfbreak custom rom CM6.1.3.


PREPARATION

Fresh install the stock rom by doing these steps :-

1. Download Sony Ericsson Update Service (SEUS) application from here http://www.sonyericsson.com/cws/support/so...x10?cc=gb&lc=en and install it into your pc.

2. After the installation has finished, run the application and just follow the onscreen instructions. If this is the first time you are doing it, it'll take some time as SEUS will download around 120MB of firmware data to your PC before it can flash to your phone. Just set the date and USB Debugging to ON.

3. Download flashtool 0.2.9.1 Beta from here http://www.multiupload.com/7H4JT35B6G and install it into your PC.

4. Connect your phone to your PC and run flashtool and root your phone by click the ROOT tab. Wait for a while and your phone will reboot and rooted.

5. Click the ASK Root Perms and make sure your phone screen is on to Allow SuperUser.

6. Click on xrecovery tab and it will install xrecovery on your phone.



CUSTOM ROM INSTALLATION

1. Reboot into recovery mode by power off and power on, once you see SE logo, press the back key a few times until you see the recovery menu.

2. Do Factory reset (full wipe), Wipe cache partition, wipe dalvik cache and battery status (in Advance options).

3. Install CM_6.1.3_[v006].zip.

4. Install CMFix_v6_v61.zip.

5. Reboot your phone and enjoy Froyo 2.2.

This post has been edited by tot31: May 17 2011, 01:52 PM

Install CM_Update_v06.zip.
is it for update rom right??

All stock 2.1 SE firmwares have the same kernel but different baseband due to country/operators radio signal for mms, sms and phone calls. For instance Canada can't use bb52 therefore they are using bb54 but fortunately for us Malaysis we don't have problems using any of the basebands.

At the moment Jerpelea's custom kernel is based on bb52, so if your baseband is other than that, you'll get problems. Same goes to roms. It depends on the chefs/devs when they are cooking/porting roms. So before you want to install any custom roms, read the first page, what is the baseband that the roms required.

thank for the info....so the performance of the phone only depends on the custom ROM u install?

yes, most custom roms have been tweak to get the best performance. All depends on the devs/chefs of the roms. Since they are doing for free, not much you can demand from them. For instance, most of the GB roms at the moment does not have the camera feature, most of the devs are waiting for the official GB rom from SE so that they can use the library to get the camera works on their rom. What I've read that, implementation of the camera is quit complicated and time consuming, that is why they are willing to wait for SE to release the official GB rom.

so now, it's all depend on you to choose the best custom roms that suits your normal usage. so far I found that a work in progress SuperAOSP Overdrive by rdannar is the fastest rom but still has some bugs with apps like Root Explorer, Titanium backup, and some widgets. the most stable and fast GB rom at the moment to me is SuperAOSP2.3.3 Stable version from rdannar too but like said before, camera does not work.

in comparison to WBCM6 froyo rom, cobrato's MIUI3.1.8v2 froyo to rdannar GB 2.3.3 SuperAOSP rom in terms of performance, they are equal. WB CM6 and cobrato's MIUI roms has everything working including camera.....so the choice is up to you....

bro..my prob still same..no signal..3 times i tried..what should i do now??

any custom kernel suitabke fir daily use? never try 1 b4

WolfBreak's CM 6.1.3 [V006] would be nice for daily rom

I won't use custom kernel yet.. Until it's really "stable"

CAN i please know if it's possible to have timescape UI in my galaxy sl phone?

I <3 timescape!!

can anyone tell me where or how can i find a timescape launcher or something.. and use 'home switcher' app to switch from touchwiz to timescape UI? please?