ooo...so between the model i mentioned just now, which model give best SQ?

torresism
ask in ICE section, here all noob in ICE.

Well,
My personal opinion is, Alpine give better SQ.
But for Alpine, you need to get above mid to higher end models, the lower end models doesn't make much of a difference as compare to the normal HU.

Not very sure of Kenwood HU, last time I had one, and the SQ was very bad...

I personally prefer SQ and stagings, but occasionally i do BOOM a bit. So my setup needs to be very flexible in terms of bass.

Changed my front speakers to Meastro Component, German brand, took the entry level model. So far, I quite like it cause even with Ori Saga BLM HU, it can kick some hell of a mid bass! But too bad our Ori HU doesn't have much flexibility on the SQ tunings...
kekeke

---

Added on August 1, 2010, 1:06 amInstalled the Component set at EA Auto, done by HowieChoo

http://www.german-maestro.de/EN/as6508.htm



But like he told me, what he can see from my characteristics, I'll upgrade soon. Hell yeah! LOL but only if I have the extra money the next time


This post has been edited by Newgen: Aug 1 2010, 01:06 AM

I m more to SQ and beside choosing suitable HU, component, amp and woofer, you need to spend a lot on sound proofing.

For SP, totally cheaper then SQ but just need a lot of volt to support.

guys, i'm living in cyberjaya. which service center do you guys recommend me to go for 40k major service and check for my breaks and engine coz my break keep giving me sounds and the engine also...

the break sound is like sometimes when we press the break it got like rubbing sound between 2 metal "eeeee" like that one. the problem is that even though i'm stepping on the oil pedal it also got that sounds like i'm pressing the break...

while the engine sound is like bird chirping sound... previously one month ago changed the AIFM then quite for 3 weeks then started to sound again...

any recommendation?

This is what I mean......
because I have told the clerk and also the mechanic when sent my car for 1st service to check the alignment but then they told me that they cannot do it......
I was like WTH, it is just the 1st service and during my parents "lenjan" for 1000KM, it is 90% on the new TAR road....(still black with no hole)......
If they did not have the equipment, still they can sent to outside with FOC to customer as I was told by the branch agent which I take the car, if anything feel not right after driving it, need to tell during 1st service and they will do it for free......

And right now my car when drive above 100KM in highway, the steering will shake like Malaysia have earthquake already even in highway.......

Can anybody who have experience to advice me regarding my situation and what should I do? If can be fix during 2nd service, please recommend me A GOOD Branch Service Centre or GOOD Authorized Service Centre near kajang, bangi, serdang and putrajaya

I accidentally bang my bumper today to a pole with my saga

Got obvious big patch of paint scratch, structure wise still ok..

What can i do to fix it ? Must I repaint the whole bumper ??

hey guy, i have a question, can we buy a new CPS 1.6 engine (halfcut)from Proton?

if got dent need to knock it out and yes better to respray the whole bumper for paint even-ess

if no knock out what will happen ? cos my door got kemek a bit..like 2cm wide and 5cm long

btw had my iafm fixed on sunday, took around 2 hours include 15k service.

i got a dent on my bumper too... but i thought the bumper is plastic? how to knock it out o??

Thanks for the reply... lucky no dent...

anybody knows where is a recommended place to respray the bumper ?

and just to spray the bumper how long it will take ?

mine is the tranquility black..

knocking out applies only to the metal part of the car. think plastic need chg unless u can try knocking it out. maybe it will break

please somebody reply me. i need to do it urgently

hi shld not take more than 1-2 day. can go call and ask them to confirm. they can let u know the cost also. call few shop to compare price. dont worry too much, its small issue.

anyone with recommendation regarding my question?

BLM got facelift soon. Backlight LED. Saw it today at proton shah alam factory. Can't take pic. If kantoi then deep shit. Look quite nice. Backside abit wider than before.

can but will cost you >10k

---

Added on August 3, 2010, 12:36 amoutside plastic but inside got steel bar or frame holding the bumper..that means the steel inside bengkok already

This post has been edited by xshiro: Aug 3 2010, 12:36 AM

ｏｏ．．
ｔｈｅｎ　ｂｅｔｔｅｒ　ｇｏ　ｔｏ　ｏｕｔｓｉｄｅ，　ａｓ　ｉ　ｓａｗ　ｆｒｏｍ　ｍｕｄａｈ　ｃｐｓ　ｅｎｇｉｎｅ　ｈａｌｆｃｕｔ　ｉｓ　ｃｏｓｔ　ａｒｏｕｎｄ　４ｋ．

erm it means iafm makes funny sound again...

and check you brake...maybe something stuck inside most probably rear drum brake

ask the nearest sc

---

Added on August 3, 2010, 12:43 amya...got...but i think its gone already...

ok, i give you some tips.. what u need CPS head , CPS ecu and wiring and intake manifold..
head and intake
http://www.mudah.my/Cylinder+Head+CPS-6498490.htm
ecu
http://www.mudah.my/Ecu+Campro+CPS-6408155.htm

bottom part, u can use normal campro punya...u can even use ur exsiting 1.3 campro

replace the normal head with cps head ...wallah...cps 1.3 or 1.6 already...

the difference between cps and normal campro, the head only got real cam profiling

---

Added on August 3, 2010, 12:51 amone day can be done...u can find workshop specializing on ketuk and paint...where do u live?

This post has been edited by xshiro: Aug 3 2010, 12:51 AM