maiden my heli. for some reason the tail is wagging so im at dual rate 80%
also my gyro gain is 17..thats too low...
but im able to hover with those
Hobbies R/C Helicopter v2
|
|
 May 27 2010, 09:43 PM
Return to original view | Post
#241
|
 
Junior Member
124 posts Joined: Jan 2010 
|
|
Quote|
|
|
|
|
May 27 2010, 10:11 PM
Return to original view | Post
#242
|
|
Junior Member
124 posts Joined: Jan 2010
|
Im using on Mode 1.
Anyway is my esc programming as in i can set the esc to detect that my battery is 3.75 and it will cut off? my esc - http://www.hobbycity.com/hobbycity/store/u...?idProduct=2164 Just a comment from the guy who set my heli, he said that my motor is very very fast, can do 3d. http://www.hobbycity.com/hobbycity/store/u...?idProduct=9021 This post has been edited by sLapshock: May 28 2010, 07:54 AM |
|
|
May 28 2010, 02:03 PM
Return to original view | Post
#243
|
|
Junior Member
124 posts Joined: Jan 2010
|
QUOTE(QiW @ May 28 2010, 12:15 PM) depends on what blades u use .. my first maiden CF blades .. 99.99% gone case when hit wood blades cannot do too high RPM .. 50% chance of surviving  http://www.youtube.com/watch?v=k9_AzqMy7EQ |
|
|
May 28 2010, 06:46 PM
Return to original view | Post
#244
|
|
Junior Member
124 posts Joined: Jan 2010
|
Haha... due to same unknown reason, it is easier than realflight, but yeah of course, hand shake the first time spooling up, eventually it get better.
Added on May 28, 2010, 8:14 pmhi guys, what do you think of this ESC? http://www.hobbywing.com/ENGLISH/ArticleSh...p?ArticleID=373 2 Features 2.3 Programmable Items: Brake Setting: brake enabled / brake disabled. Battery Type: Li-xx (Li-ion or LiPo) / Ni-xx (NiMH or NiCd). Low Voltage Protection Mode(Cutoff Mode): Gradually reduce the output power / Cutoff the output power. Low Voltage Cutoff Protection Threshold (Cutoff Threshold): low / medium / high. Start Mode: normal / soft / very soft. Timing: low / medium / high. Reset: reset all the programmable items to its default setting. 2.4 Full Protection Features: Low voltage cutoff protection / Over-heat protection / Throttle signal lost protection. ---------- can you guys explain to me what the features means? all that i pasted? thanks... Added on May 28, 2010, 11:02 pmSECOND MAIDEN. http://www.youtube.com/watch?v=uK7VseyfXW8 This post has been edited by sLapshock: May 28 2010, 11:02 PM |
|
|
May 29 2010, 12:08 PM
Return to original view | Post
#245
|
|
Junior Member
124 posts Joined: Jan 2010
|
QUOTE(QiW @ May 29 2010, 01:23 AM) 2nd time is no more maiden laaa its 2nd flight .. hahahahaa do u have a hobbywing ESC ?? Added on May 29, 2010, 1:26 amvery well flown ... for 2nd flight did i not say SIM pays back alot ?? hahahahaaa i think it is time to take off those training kit already u can fly without it for sure ... just have a little bit of confidence Yeah true bro...i think if u didnt advise me on practice on sim first, i would already crash my heli.. Take off? Dun wan la..i want to do alishamano routine first..then i might think of taking of those..haha... Anyway, actually, my gain is very low at 17..if i put on 40 ..the tail wag like crazy nw i haf this prob.. Tail is spinning to the left..i have to input rudder to left during hover.. Is it bcoz of 1. My tail servo rod to tail rotor not straight? 2. My gain is too low? Added on May 29, 2010, 12:28 pmtrue man, haha...if i didnt listen to ur advise on practice on sim, i would already crash it. Anyway i do haf a prob, my tail is drifting to the left, i need to constantly keep the rudder input to left to keep it tail in. is it bcoz of: 1. Hbk401b gyro is set too low at 17? (if i set it at 40, it wag like crazayyy) 2. My rod from tail servo to tail rotor is not straightened? (it does curve abit...) im nt using hobbywing esc, i heard its very good, im currently using turnigy esc 30a. Not sure if i need to upgrade my esc to hobbywing... This post has been edited by sLapshock: May 29 2010, 12:28 PM |
|
|
May 29 2010, 03:45 PM
Return to original view | Post
#246
|
|
Junior Member
124 posts Joined: Jan 2010
|
what is punch? Always heard it, but dont know what it is. Anyway approximately how many minutes after flying to touch the esc?
How to straighten my rod, mine is kinda long, can i cut it? Added on May 29, 2010, 3:53 pmok i get it, i know what is punch now, it is extensively used in all tareq al saadi flying video... I tried doing tht, but my heli cant punch maybe they set the beginner curve for me...so that it is not sensitive So how do i adjust this punch thingy? This post has been edited by sLapshock: May 29 2010, 03:59 PM |
|
|
|
|
|
May 30 2010, 01:49 PM
Return to original view | Post
#247
|
|
Junior Member
124 posts Joined: Jan 2010
|
QUOTE(QiW @ May 29 2010, 10:04 PM) punch = just whack throttle only lorrr How to set my idle up throtle curve?if u have set up idle up properly ... go to idle up mode and suddenly give it lots of pitch to make heli jump up my idle up curve is straight line pitch throttle curve is 100-97.5-95-97.5-100 for me plus u got training gears ... very heavy .. heli cannot jump oso laaa normal u check batt after flying .. and then adjust your flight time according to your battery ... mine is just 4:20mins and land i still get about 3.75v per cell after u land then just touch your ESC and see lorr Added on May 29, 2010, 10:05 pmpunch = just whack throttle only lorrr if u have set up idle up properly ... go to idle up mode and suddenly give it lots of pitch to make heli jump up my idle up curve is straight line pitch throttle curve is 100-97.5-95-97.5-100 for me plus u got training gears ... very heavy .. heli cannot jump oso laaa normal u check batt after flying .. and then adjust your flight time according to your battery ... mine is just 4:20mins and land i still get about 3.75v per cell after u land then just touch your ESC and see lorr Anyway, this is my TURNIGY TYPHOON 2215 SPECS Turnigy Typhoon 2215H Brushless 450-Size Heli Motor 3550kv Specifications: Dimension: 35mm x 28mm, 51mm(with shaft) Weight: 63g (kv3550) (not including connectors) Voltage: 2-4S Max current: 20~28A Diameter of shaft:3.17mm Length of front shaft:16mm ESC: 40A Turnigy Typhoon 2215H for 450 class Helicopters. BUT IM USING TURNIGY PLUSH 30A ESC!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Shit man?! Lucky my rpm set very low, only hover2... what happen if i continue? I should get 40a ESC RIGHT? any reccomendation?? |
|
|
May 30 2010, 11:04 PM
Return to original view | Post
#248
|
|
Junior Member
124 posts Joined: Jan 2010
|
thanks for the supportive comments, nevermind, i will prove to you guys i'll hover in all orientation and post a video, then must promise me to reccomend me good electronics and the idle up. haha.
so i dont have to worry about burning my esc la, hmm.. im a firefighter as a career, so some things are not hot enough,so how do i know my 5 seconds i your 1miliseconds  !This post has been edited by sLapshock: May 30 2010, 11:07 PM |
|
|
May 31 2010, 10:17 AM
Return to original view | Post
#249
|
|
Junior Member
124 posts Joined: Jan 2010
|
Hahaha... as long as it didnt burned my ESC then i think i'll stick until i want to change the motor lor.
should spen the money to buy battery first. Added on May 31, 2010, 10:32 amok guys, this is my attemp of flying in my house porch. http://www.youtube.com/watch?v=XbVb5iar0jQ if you guys notice, my tail wags a bit though my gain is already at 17 and my tail drift to the right... during 0:16 to 0:25 i hover it handfree just to show my tail wag and tail drift, coz during hover, i will play a lot with stick... any way to correct this? This post has been edited by sLapshock: May 31 2010, 10:36 AM |
|
|
May 31 2010, 12:07 PM
Return to original view | Post
#250
|
|
Junior Member
124 posts Joined: Jan 2010
|
does unbalance blade have a bad effect on the heli?
i dont have tools to balance my blade, is there anyway i can use household items to balance my blade? |
|
|
May 31 2010, 04:25 PM
Return to original view | Post
#251
|
|
Junior Member
124 posts Joined: Jan 2010
|
go for 450 clone!!! i just bought align blade...$19 singapore...i hope it will be betterrr... oh and carbon fibre tail blade too
This post has been edited by sLapshock: May 31 2010, 04:51 PM |
|
|
May 31 2010, 04:52 PM
Return to original view | Post
#252
|
|
Junior Member
124 posts Joined: Jan 2010
|
go for clone la, coz u will upgrade to 500 later
 |
|
|
May 31 2010, 05:34 PM
Return to original view | Post
#253
|
|
Junior Member
124 posts Joined: Jan 2010
|
shit. i just use up my batt until 9.9. if i do it the first time, does that mean i FU**ed up the battery liao???
|
|
|
|
|
|
May 31 2010, 05:56 PM
Return to original view | Post
#254
|
|
Junior Member
124 posts Joined: Jan 2010
|
where to buy the small timer ea for me to stick on my tx???
|
|
|
May 31 2010, 10:28 PM
Return to original view | Post
#255
|
|
Junior Member
124 posts Joined: Jan 2010
|
|
|
|
May 31 2010, 11:54 PM
Return to original view | Post
#256
|
|
Junior Member
124 posts Joined: Jan 2010
|
my gyro gain is 15 leh, what do you think
|
|
|
Jun 1 2010, 06:11 PM
Return to original view | Post
#257
|
|
Junior Member
124 posts Joined: Jan 2010
|
alah...when i fly also scared scared lah.. Actually nt that bad, u play sim raptor30 with 150physics...
if u can hover that well, u confirm plus chop can hover trex in ur living room already. Serious shit. 1. Hover tail in (done) 2. Hover right side in (done) 3. Hover left side in (in progress) 4. Hover nose in (coming soon) Qiw, let me see if i correct regarding my idle up understanding. Idle up is when the rotor will automatically spins so you can control the - and + pitch only. Certain percentage of of throttle power can be set throgh idle up throtle curve say 100, 95, 80, 95, 100. So when u invert ur heli, you put it on negative pitch without affecting the rotor rpm. Unless in normal mode when your negative pitch equals to slow rpm. Am i right so far? |
|
|
Jun 2 2010, 02:25 PM
Return to original view | Post
#258
|
|
Junior Member
124 posts Joined: Jan 2010
|
Guys,
i mod my gyro according to the video http://www.youtube.com/watch?v=4mI7gretwM0 now, my gain is +30 no more wags, but not solid rock holds tho |
|
|
Jun 2 2010, 09:25 PM
Return to original view | Post
#259
|
|
Junior Member
124 posts Joined: Jan 2010
|
YOU BOUGHT IT FROM KELADI EA BRO?
|
|
|
Jun 2 2010, 09:40 PM
Return to original view | Post
#260
|
|
Junior Member
124 posts Joined: Jan 2010
|
Oh i see, what you bought? Imax B6?
|
|
Topic ClosedOptions
|
| Change to: |  0.0441sec
 0.59
 7 queries
 GZIP Disabled
Time is now: 1st December 2025 - 02:41 PM |
All Rights Reserved © 2002- 2025 Vijandren Ramadass (~unite against racism~)
Powered by Invision Power Board © 2025 IPS, Inc.