seriously nice job bro!...

superb modded RaVen...

2day update.. alrdy receive my parcel.. thanks to nej again.. n to barry7 form langkawi, thanks bro..

the parcel i receive is my fitting





see my 2nd psu? hehe..





i need to find 1/2 tube.. need it for my drain barb.. anyone got some? just need it around 7inc..

temp im using 90'.. coz 2day want to try run.. want to seek for any leak..



GOT LEAK... shit..



leak from mcw60, join on fitting..

now alrdy ok.. using ptfe.. thanks 'macha'

---

Added on August 25, 2009, 10:05 pmhow to use this photo uploader.. http://www.flickr.com/ ... never use it b4.. my link http://www.flickr.com/photos/41762485@N05/

This post has been edited by sopen2003: Aug 25 2009, 10:05 PM

careful oh >_<
since it's coolant, not mineral

can you take a pic of just the gpu block on your X2?

Fully loaded lulz. Your setup is great. You making me jealous!

some update last nite n after 'sahur'..

last nite, im try to plug on my drain barb.. im force 1/2 barb into 3/8 tube.. damn hard work.. nearly 1/2hour to make it success ..



cant tahan to test wc on real hdware..



my drain tube.. at 90' fitting..







still got some leak.. will try to add more ptfe tape, hv try to change fitting. but worst..

full view..



only pwr up by 2nd.. to test on pump, fitting, block, fan.. n to place all hdware into it position..

cant 'tahan' anymore.. rig 1/2 way to finish.. for about 3hour im running wc without pwr up rig (to seek for leak).. it ok..

just finish install windows.. running stock only.. n the result..

waaaa nice dude!!!...really love the color & WC kit

bro,

nak tengok time malam macam mane..

post some pic...

minggu nie keje shift mlm la.. so mlm tak ader kat umah.. siang jer..

kena tunggu till next week.. n nk siap kn sleeving gak..

-------------------------------------------------------------------------------------------------------------------------------------------------------

some update.. due to my pump nearly blocking pcie pwr (8pin + 6pin).. *just notice it when alrdy test run this rig.. so i might jumper the 8pin to 6pin. this is coz the space is so limited.. lucky, im still not doing sleeving for both 8 n 6pin pcie cable

!----
!---- (6pin pci-e)
!----
!
!
!
!----
!----
!---- (8pin pci-e)
!----
!
!
!
!
!
!---- psu (8pin pci-e)

the 6pin pcie pwr will be tap on 8pin pcie connector

btw, my mmod sleeving alrdy arrive on 1st sept thanks to nej again

aduhh next week kaaa...faster bro

Hi,

Wanna ask, the interior is still black for your RV01 after modded? Curious

i got hard time to do update this week.. a bit bz.. sorry ..

yup.. black.. but in future, im still not sure

but most likely, black


------------------------------------------------------------

some guide for NEW CONNECTOR n MODULAR that i think the best to do sleeve.. do hv some comment on it..



hahah..

we start with what we needed..



the sleeve u need..



cable.. black if possiable..

ok.. we start by cut the sleeve.. *if 24pin, cut it into 24pcs.. length is up to u..



use tape, to tape ur cable..





as u know, im using 2 diff length of heatshirnk..





dont cut ur cable 1st.. heatshrink both end of ur sleeve 1st.. then pull ur sleeve (tight ur sleeve)
how to say it.. haha.. *make sleeve to grip ur cable !! this step is really important to hv good sleeving

after u alrdy feel it enough grip.. cut those cable.. *around 2inc of length from heatshrink end..



use a tape to guide u.. this is for length u needed *if u want it lor..

put ur 2nd heatshrink..



shirnk it from bottom 1st.. then remove that tape..

!!repeat the step for both end..



*since this is only guide.. i just do it roughly.. not same end..



use knife to cut ur cable.. DONT cut the sleeve..



both end been cut, n ready to be solder/clamp to atx pin..



This post has been edited by sopen2003: Sep 11 2009, 06:16 PM

great explanation
i would like to suggest that the post be made into a sticky by mods

uncle ianho...could you help us out

haha.. 2day i went to jln pasar.. buy rivet gun, n pcb.. will do n update 2moro..

for the pcb, i plan wat to make a pcb (back plate hdisk bay).. so it will be something like an hot swap hdisk..

the pcb i plan to do..







This post has been edited by sopen2003: Sep 12 2009, 08:12 PM

i really need help on this.. hv someone sale or hv look something like this..

http://forum.lowyat.net/topic/1162260

uglyvamp got this thing at his shop. i saw it just now when in shopping something at his shop... why dont you ask him??

where will the hot-swap area be?
is it going to be in the 5.25 bay area?