@xixo_12, ah_khoo

Thanks.
Kinda disappointing.

Refer to this thread. http://forum.lowyat.net/topic/591961

-pWs-

deneb can't do dual smp meh?

Can. Anyone tested w Dual SMP?
Thanks again.

-pWs-

bro, which client should i use? i'll try tonite w/ 4 cores enabled if i have d time.

mite need some guides on how to setup & run dual smp... me noob in f@h...

This post has been edited by ah_khoo: Mar 11 2009, 02:45 PM

Here you go bro.

Thanks for the effort.
http://forum.lowyat.net/index.php?act=Atta...=post&id=586718

-pWs-

i know bro, it's kinda dissappointing..

i'm oso waiting dual smp result
but i thought idragon use dual smp

dual smp mean install d client twice? i'm lost...

Just created 2 different folders w 2 different Machine ID.

-pWs-

ya... too high NBfreq and HTlink will coz ur sys unstable, js try to push a bit ur vNB,vHT, c hw it goes, BTW care on ur NBcooling too

This post has been edited by cdlim87: Mar 11 2009, 04:00 PM

it's ok to have high nb freq as long as enuf juice provided, not so sure bout ht link thou...

WTA:
as my old knowledge serve me that HTlink even OC oso will dun help in performance..

is this right? or it does help in performance act??

wat kind of performance? if it do.

in am2, higher htt link gives slightly better performance in spi as pointed out by bro dblooi b4, not sure for agena & deneb. nb freq oc seems to be more useful to boost performance for d latters.

Now stable in 258MHz Bus Speed & 2322MHz NB Freq @ 3.6GHz

My crappy MB tired any setting cant push up over 3.6GHz stable blend test in PRIME95 test, even PII 940 increase to 1.5VID @ 3.7GHz still unstable and in 1.5VID is VERY HOT AND UNSTABLE

but now I use this setting performance and stable better than setting before



My MB only have NB VID setting, but only can reach +0.1V

So I increase +0.1 NB VID but still unstable in 2700MHz HT Link @ Prime95 blend test

How to use BAR Edit to adjust NB freq?

I noob in F@H

What is Dual SMP? How to config dual SMP in F@H SMP Client?

This post has been edited by idragon: Mar 11 2009, 05:57 PM

Hallo to all my fellow clanners.......

I will be back in maybe next or the other next week with new ocing result hopefully... as now i am still hunting and looking for the right items to get...

and need some assist here

1. pc p&c 610 or 750w

2. DFI or ASUS

3. Ram 800MHz or 1066MHz

p/s: the "duit tersepak" is in the house now .....

finally got something for my torrent rig
[attachmentid=841458]

@idragon,

dual smp info all in F@H thread.. u can read there how to setup it,
it will utilize all core...

This post has been edited by xixo_12: Mar 11 2009, 06:42 PM

oh ic ic..

i say if u really have enuf $$, go for a better spec u can,
mean i vote for 750W and ASUS

for the ram, normally a good chip 800 can do better in OC while 1066 will not so OC able,
but thn the total speed thy can hit is almost the same, so depend how u want ply it..

if u want ply with a super high HTT oc, i would like to vote for 800, else 1066 oso ok..

that is my opinion..


@idragon
yup, 940BE vy sensitive to temp, if u cnt keep the good temp for it i tough to get stable at higher vCORE and the vice versa

Sorry for a noob question as I cant search it(duno use wat key word).

Problem is that I've set the fsb value in bios..but when comes into window, open up cpuz it still show original clock.

Btw, my mobo is MSI KA790GX.

there is possibility, ur oc not stable, n it auto revert to standard clock

but then...i'm only set it at a very low clock..like ori fsb 200 i set it 220.

what chip ur on bro?

i finished w/ installin d client & creatin d shortcut, after i double click on it, nothing come out...

This post has been edited by ah_khoo: Mar 11 2009, 11:01 PM