Its normal, my Q9450 is running at 3.2ghz using 1.2vcore has 54, 52, 49,49 on idle. hahaha

Typo error I guess, should be 1.XX for the vcore.

-pWs- : Here's my SS



Ur Q9300 oso power oledi

This post has been edited by jy14: Mar 7 2009, 12:59 PM

The speed here is not the max yet, previously tried 3.45 on the m2f for my customer's board, but his value ram is stopping it from going further. I noticed this was a good batch, the "B" batch, so had to decide quickly to get it. Using it on a DFI P35 DK now.

its stated on the box. On the proc also its written: L8XXAXXX, the "a" can be "b" which i read in some forum saying the "b" batch r better for oc, not sure how true, so i just try my luck.

This proc inside Sugo ? Wow, must b either sensor spoilt or ur contact with the hsf not so good. What cooler u using now ?
P45 JR oc not the same as ur gigabyte ? should b quite similar i guess, only asus is abit different.


efilah: wat rams r u using ? So far, ur oc seems very good, just a little more push and u'll reach the 4ghz mark. temp is good too.

rsangel: I'll suggest the AXP-140. Haven't got the chance to test it out yet, but shouldn't perform any worse than the Silverstone NT06 or enzotech. Not too sure how it fairs against Noctua's C12, need some1 to review it. reputation from TR should assure u get a good temp out of it. If u got time, try to re-seat ur proc and the hsf to make good contact, and also clean the surface of both sides with the alcohol or arctic cleaner b4 mounting it back with new layer of tim. For rams, DDR2 for 2gb kits nothing beats any D9GMH or D9GKX chipset, while for 4gb kit, dominator 4gb ddr2 1066 with the fan kit is the best option. But i can't remember off hand which ver is it that would b good for oc. Otherwise, G.Skills black pi 4gb DDR2 1000 would b nice too.

efilah: well ur proc seems to show consistent reading on both real temp and core temp. On myside, if u saw my screenies, it shows the real temp reading and the core temp reading has a difference of 10C, so, for safety, i'll assume core temp's reading is true for now, just to make sure i don't fry anything. I've yet to research further on which reading is more accurate, so i can't advice u much now, but will inform u if i've found any new info. For the rams, same advice as i've given to rsangel. Here many sifu oledi start playing with i7, so left us to play with the quaddies at the moment.

This post has been edited by jy14: Mar 8 2009, 03:43 AM

rsangel: I think its quite rare to find such size, will inform u if can find it. TR in SG is quite reasonably priced close to MY, depends purely on conversion rate at that time. Its this month is it for the convention ?

efilah: oh, ok i'll try that too. Do grab the dominators from seamonster if u r desperate for it. Most dominators are good and stable.

Yeah taiko OC4/3 Happy B-day.


rsangel: stock cooler its expected of such temp bro. Just don't stress too much b4 u burn ur proc. hahaha. Is there any way u can mount a fan between the heatsink fins at the top and the base of the heatsink ?



I mean the 40mm gap there, u might b able to find some fan to fit there and push the hot air into ur psu inside ur sugo.

-pWs-: Bro ur TRUE can't bring down the temp ?

I'm using a TRUE with Scythe S-flex to get the load temp around 68C range with ambient of 30c.