what material do you want to use bro? Alu or Plexi ?
All you need is a drill,jigsaw,filing tools,most important is patience.
[WTA] How to do a motherboard tray, Help me if can
|
|
 Jul 13 2008, 01:40 AM
Return to original view | Post
#1
|
 
Senior Member
2,827 posts Joined: Mar 2007 From: MALAYSIA   
|
|
Quote|
|
|
|
|
Jul 13 2008, 11:42 PM
Return to original view | Post
#2
|
|
Senior Member
2,827 posts Joined: Mar 2007 From: MALAYSIA
|
QUOTE(Pon&Zi @ Jul 13 2008, 10:40 PM) if i wanna use alu is it harder than plexi ?? wat the different between alu and plexi ?? which is better ??   2nd-To do a motherbord tray,you must know the thickness that you need to support all the riser (screws ),the motherboard,gpu ETC. 3rd-I think you can use acrylic as a start.Alumunium is damn expensive and kind of hard to get.Other than than,acrylic is easier to cut since its only a plastic material. 4th-Try to get all those materials you need 1st,then do a review on the net.You can ask anyone here to help you.  |
|
|
Jul 14 2008, 12:04 AM
Return to original view | Post
#3
|
|
Senior Member
2,827 posts Joined: Mar 2007 From: MALAYSIA
|
QUOTE(m2n-e @ Jul 13 2008, 11:56 PM) anyway.. again.. good luck to u and to me. wakakka.. gonna DIY my casing like that oso. You also wanna make a motherboard tray bro?? |
|
|
Jul 14 2008, 12:15 AM
Return to original view | Post
#4
|
|
Senior Member
2,827 posts Joined: Mar 2007 From: MALAYSIA
|
QUOTE(N's @ Jul 14 2008, 12:07 AM) I called door hinge. What's that for? I mean what it got to do with the motherboard tray? |
|
|
Jul 14 2008, 12:21 AM
Return to original view | Post
#5
|
|
Senior Member
2,827 posts Joined: Mar 2007 From: MALAYSIA
|
QUOTE(Pon&Zi @ Jul 14 2008, 12:16 AM) by the way bro... is it ok to do a motherboard tray with acrylic cause it sounds weird... because my thermaltake shark is not transparent at the side so can anyone help me Yes,its not weird to make a motherboard tray with acrylic.Try to imagine a full transparent casing by sunbeam.The motherboard are made of acrylic. For the side panel at the motherboard tray side,just leave it to non-windowed. Just focus on the left side panel. |
|
|
Jul 14 2008, 12:24 AM
Return to original view | Post
#6
|
|
Senior Member
2,827 posts Joined: Mar 2007 From: MALAYSIA
|
QUOTE(Pon&Zi @ Jul 14 2008, 12:22 AM) I think maybe alu is better cause can conduct heat some more and my casing is alu... Using a alu is also not a bad idea.Well,its up to you to decide.I am just giving opinions. see this website my tray is remove without the back panel so now i wan it the out jz like that raidmax one  http://www.thermaltake.com/product/Chassis...k/va7000bwa.asp i will show u the pic if anyone request Good luck to you bro.  |
|
|
Jul 14 2008, 10:09 AM
Return to original view | Post
#7
|
|
Senior Member
2,827 posts Joined: Mar 2007 From: MALAYSIA
|
QUOTE(Pon&Zi @ Jul 14 2008, 08:45 AM) TQ for ur opinions i wan to ask have u make a motherboard tray before ??? Haven't make a fully custom made.I only done a touch up to them.  Jz wan to ask only because u look so PRO |
|
|
Jul 14 2008, 10:15 AM
Return to original view | Post
#8
|
|
Senior Member
2,827 posts Joined: Mar 2007 From: MALAYSIA
|
QUOTE(m2n-e @ Jul 14 2008, 10:12 AM) @offtopic huhu...sabar bro. aih... tak abis2 ngan rumah kucing. huhu.. project tangguh, funder tak cukup duit. |
| Change to: |  0.0146sec
 0.57
 7 queries
 GZIP Disabled
Time is now: 21st December 2025 - 09:06 PM |
All Rights Reserved © 2002- 2025 Vijandren Ramadass (~unite against racism~)
Powered by Invision Power Board © 2025 IPS, Inc.