You can break 80'C with only 1.4v...

It depends on your ambient temp. Previously I had 1.4Vcore in an air cond room and load temp can hit up to 70C w/ stock cooler.

No no... You only pump when its not stable enough.

Around 1.41v... Last time need less, now need more... Processor dieing

---

Added on for the line.
1.3856v in BIOS selection, BIOS reads 1.376v and CPU-Z reads 1.376~1.392v to get stable 333x9 3Ghz

E2160 should be able to get 3.0Ghz with stock vcore.. 

85 on TJunction

My E2160 @ 333*9 3ghz 1.3811v in BIOS selection, BIOS reads 1.3600v while CPU-Z reads 1.352~1368v.

its depend on what mobo u r using...last time when using ds3 board..i also can do 3.0GHz at stock...but after change board to Blood Iron...need to feed voltage

kmarc...my Blood Iron board have stable vdroop at 0.032v...my stable setting

3.0GHZ 333x9
vbios = +25.0mv
CPUz idle 1.360v
CPUz load 1.328v

well for my e2140 with the abit ip35-e, i can do 3.1Ghz with 1.325V but yes again, mine is a gem

here's my e2140. bios set

3.25ghz @ 1.325v
3.4ghz @ 1.425v
3.6ghz @ 1.525v (trying to get it stable)

yeah kmarc something like that lar.. but mine was picked by the master bryan ler. he is sifu in picking the best hardware!

Waa...Can I ask  him pick one for me too?

-pWs-

Hi sifu2 how to overclock Ram?
now im stuck in Ram frequency i think.
mine Kingston DDR2 667 2 X 1G Hynix FP-Y5 chip.
can't increase my ram freq over 750mhz
timing is 5-5-5-15

1.90v...
try increase to 2.2v..but still the same..
now i put Vcore more..
1.60v..walao! insane edy

18.718s|PGV3910|E2160 Conroe 1M L2 Stepping with Silverstone NTO2|3.46Ghz|Abit AW9D-MAX|Kingston DDR2 667 2X1GB|750Mhz|5-5-5-15|
My L2 stepping is better than my friend MO stepping(new batch) i think

maybe my Ram not good enough..wanna borrow my friend DDR2 800..
fried it like hell

now one to suicide my mobo..
put higher mch volt...
wait n see
if nothing happen i'll post my highest score.
but if kebabom..paham2 jela.

to all sifus here.. which clock setting is suggested by u all to run at 24/7?

i tot nid to stress the ram togater? no nid?? 3.0 @ 1.3v is for 24/7 setup.. the ram runing @ 333mhz 3-3-39 better or 400mhz @ 4-4-4-12?

My friend can achieve 3.2ghz with stock HSF but 75c when stressing.. Mine the highest 3.1ghz.. a bit more than that the temp rise near to 83c.. later wan change the HSF.. Any recommendation? Thinking of IFX or 120 ultra extreme.. Btw, thanks for your help.. will try it.. nice ram u got there..

newbie reporting in 
Just get some new toys,
G0 E2140 (Check CPU-Z) & Elpida chipset KVR

found some issues 
1) Blood Iron couldn't post with crucial 10th anny installed 
    Anyone try 10th+ BI combination before?
2) Blood Iron NB heatsink, can i remove it without voiding the warranty? It's very hot and kissing my HP-1204 air cooler 
[attachmentid=454144]
3) The ram slot hard to close/open with gc installed
[attachmentid=454145]
4) Not enough JFAN port to use ( 3 only) 
    I have 4 JFAN ports for my AMD matx mobo TA690G 
5) Issit possible to flash LAN Party UT or DK P35 bios into blood iron? 
    I need CMOS reload function badly   

guidance & suggestion are needed, thanks in advance 
will try to bench further once I'm free