reporting in to new version. hope to see my hardwork updated (2.85, check old thread, thx -pws-)

wanna ask u guys, for the everest system stability test, is it more difficult to run for long time compared to orthos, prime or other stressing programs?

everytime run that one sure reboot after some time.

but i can run everything else orthos more than 12 hours superPi32m, 3dmark06 and others. just this one will fail after some time.

anyone wanna give it a try and let me know if u can run it for 6 hours at least stable?

hi guys, im back again for help

my setup is as follows :

CPU : AMD Athlon64 X2 3600+ AM2 Brisbane @ 2.85GHz
MOBO : Biostar T-Force TA690G AM2
RAM : 4GB Kingston Value RAM DDRII 667 Hynix FP-Y5 (3 pieces HY5PS12921C and 1 piece HY5PS12821E)
PSU : HEC WinPower 480W



currently my FSB:DRAM is /6 which i can pick in the bios, under the HT frequency i think (200 for 1, 400 for 2, 600 for 3, 800 for 4, 1000 for 5) so i picked 3 to get 800MHz on my ram.
2400/3~800

my ram voltage is up at 2.35.

my target is to get 2.7GHz (on stock vcore which i can do previously but it gave me 676 on the RAM only) with the RAM@800MHz or more.

i previously tried 2700MHz with the HT frequency at 3 to try get 900MHz on the RAM but it didnt boot.

can anyone tell me what im doing wrong? anyone with similar RAMS and what is ur limit on the RAM?

I cant think of any other way to achive what im trying. one more thing, the CPU multiplier (which is the NPT FID right?) doesnt seem to be changable.

any guidelines on what i should be doing?

update, im able to get 810 on the RAM. 850 cant start up.



edit : sorry for double post. i thought the post would auto-merge one

btw, will RAM timings affect my ability to get higher clock on the RAM?

This post has been edited by awh85: Feb 23 2008, 11:05 AM

icic.

bcoz the memory bus is linked to the proc frequency, is there a way i can get my RAM to run at the 800MHz but at a higher CPU speed (aiming 2.7GHz).

i cant seem to think of any numbers/ways to link it.

not sure if this is the right place to ask or not but will a thermaltake blue orb 2 fit on TA690G?

im not really sure but i think it will interfere with 1 or 2 ram slots so either the ram slots cant be used OR the rams have to be installed onto the slots first and if the RAMs need to be removed, the Blueorb2 has to be taken off first? (estimating that the RAMS would be slightly under the fins.)

actually, i wanna ask something. does the required vcore actually depend a bit on the motherboard as well? for my processor (3600+) i need more vcore to get to the same speed as others. either that, or my oc method/skills suck.

i think the stepping is same lo. G1 3600+ brisbane.

reading as in what? u mean like trying to diagnose the problem?

for my mobo, enable means setting to 2T CR.

did u change the correct one? (maybe the u left it at auto and changed 12/15 for something else) or maybe bios problem?

for me, if its too tight, it wont post. if it can save (in bios) and enter windows, i think maybe tras auto adjust coz too tight maybe? (dunno got such thing or not)

or maybe he can just try leave the tras as auto and use that setting and see what value it is given.

added : or maybe he can double check to see the value he changed was actually tras.

This post has been edited by awh85: Mar 11 2008, 02:45 PM

ya, i needed to increase my NB voltage by just 1 level to get a higher oc on my rig. no harm done, i can touch the nb heatsink and the heat is still ok.

wanna ask, if im using a pair of crucial value pc5300 D9DMH, what trfc values can i use? how about MAL?

i thought he just said it cant boot WHEN he increase vcore.

my gosh, something really wrong with my eyes recently

guys, may i know which one is better? a tighter or looser MAL value? in terms of performance. and what is the MAL actually for?

This post has been edited by awh85: Mar 14 2008, 01:55 AM

actually i just found out that alphamatic is same row as my office

looking for a better cooler first. now still on stock, damn hot when i try to oc higher.

i thought your F3 is a better OC-er? why do u need so much vcore to reach 2.9? for my 2.85 i just need 1.35v.