Linx more stressful than Prime95.

-pWs-

the heat really the problem for clocking up the kentsfield' zzzZzz 
itchy to oc back, but no gears to cool it down 

btw, guys... once ur cpu temp. reaching 7x-8x C'
i wonder what's ur nb temp.? , since it's close enough to hsf.

ok here it is.
10 loops of linx and it still stable with a 90C,but the temp getting 90C max, im afraid it gonna burn my processor, but i usually get 60-65C on load while playing games 24/7. Guys, should i lower my FSB ? or is it ok with this setting ?
[img]http://img146.imageshack.us/img146/6263/asdasdve7.jpg[img]

I just lap my processor but i am only getting about 3c different, is it i have apply too much as5 on it, i apply small amount on the proc n small amount on the heatsink, is it alright. secondly why small difference only.

Presently doing 3.4g after lap my true n prc @ 1.4v before 3.2 @1.325. Question is i need to pump in so much exta voltage to get 3.4g stable secondly i am getting the same temp as before for 3.4g compare my previous 3.2g, thats means to show there is improvement on the lappng but still not satified becos getting around 61-60-55-52 full load for more than one hour, whereas i see some forerummer getting below 55c n higher proc voltage, any ideal why.

Improve of 5-6c after lapping but still my Q6600 @ 3.4g voltage @1.4 only but temp seem a bit high at 61-60-55-52c full load. Is it possible that applying too much of AS5 can be the cause of high temp.

hmm... too high for me haha

for me, i will never go 60C during load !

wat u do till full load for 8 months @@

Hi, just want to know whether heat is the main killer or cpu voltage, i mean heat will made your cpu die faster of voltage.

500x7 my pc will hang after roughly 10 minits like that, which again, i blame my ram, because my ram's been oc'ed from 1333 to 1666....everytime stress test, exactly at that time it will hang... havent tried stress testing at 1333 though...

445x9 not stable too, because my vcore is just 1.616 hahaha... i guess i need to up to 1.63 and above for it to be stable... one thing about my mobo is, when i stress test, instead of vdrooping, they increase the voltage instead... quite good oso hahahaha... btw im not using any water cooling, im just using air cooling... idle temp at 1.616v is 49~51c, while when i managed to stress 2 cores, the temp reading was 79c @@

letting go of my proc next month de .... so for now, trying my best to go as fast as i can hahaha

BSOD usually occur when there's problem with your hardware, rarely its about problematic windows.

driver clashes will also bring u to the blue world right?

-=ProtozuaqS=- and uzairi
if u go over about 4.0ghz or smth try 1.6/1.7
it will get u into windows
or maybe there was some freq with the rams

im back... just changed the jumper than allows me to pump up to 2.1vcore!!...  cant seem to go 4.45ghz at 1.85v oso haihhhh, POSTed, then halfway scanning sata drive, terus hang @@.... my guess temperature too high, cant load properly hahaha... just a few minutes at 1.85v, my fans are exhausting out warm air @@.... looks like im gonna need dry ice or better... looking for it now, wait ya~!!

That is the power of real man liquid cooling,not those toy cooling

Ok, wow, thats low for a load. U can push some more for higher freqs

1.52v looks to be ur wc's limit ... but very good temp for 1.4v @@... mind telling me ur wc setup? @@@@

It is a toy pump that work for single block system,it is good for its price

Wanted to survey what's the max voltage you all usually go until with Q6600?

I'm kinda new in overclocking world, and now my Q6600 is running 335x9 at 1.4v, and I know its not so suitable cause the voltage is too high already ... I think.
I wanna ask, what will happen if the voltage has been set too high?