Is my OnePlus 7 (nonpro) water resistant sifus?

Hi guys, a bit of update on my quest of screen protectors. Just installed x-one stealth armor. Replacing the hydrogel SP (which is still the best so far).
This xone stealth armor wrap the sides of the device. Surface smoothness....meh. Quite sticky. But better than Ringke dual easy SP (hence the price).
Case compatibility....because it wraps around the device, it adds thickness to the sides. Spigen being the most tight fit, of course hates this SP. My guess is even the most forgiving case would hate this SP.
The positioning of the SP is favoring the bottom side for the button holes to align perfect. This will make the SP not covering the upper bezel. I aligned the SP a bit towards the upper side, just on the upper bezel line. Even with that, the SP distorted on the bottom side with all cases. This will be off immediately after writing this.
Personally, for this price....hmmm.....
Maybe it is not intended for it to be paired with a case....maybe.....but without a case....the back is....hmmmm........hmmmmm....... disappointed.
Another disappointment, received email from dbrand, the grip will be delayed until late july...hmmmmm......

It might sound silly, but i have to ask, once the glue is cured, will it be easy to remove the TG? Quite afraid to try the full uv glue TG 😅

let me answer this for you haha, i'm the supplier of the UV glue TG bro StratOS using, nothing to be worried of, not something new for this technology, i've been dealing with this UV glass for more than 2 years, i would say it's only a 5-10 seconds removal, no special tools needed. just peel and good to go, none of a single drop of glue will be leaving on your screen, and the best part is, phone's original coating will be still remains too. All tested and proven

best still if you're on KL, i do provide installation together

I am using OnePlus 2 and thinking for an upgrade. Hard time deciding between OP7 vs S10e vs P30

Any Whitedome Temp Glass for 1+7 Pro seller here ?

Any1 experienced problem of oneplus7pro randomly switching 4g to 3g during online gaming?
I have to use an app to force to 4g.
Not because of a weak signal.

Telcos network not stable

Hey guys, anybody knows the warranty info of op7 by xianfeng?

I checked their website and it contains nothing.

Hey Bros.. any issue with tmax tempered for op7 pro? Does it stay sticky ? I read some said some bubbles coming up? About to make an order for it.. will diy... Thx

Hey guys, a while back I said that the hydrogel ~ RM13+ was the better version of hydrogel out there. Turns out the oleophobic coating did fail after 3-4 days of usage. The first few days were flawless, almost glass smooth. But after that it went bad pretty quickly.
Then, I installed TMax TG bought from sakurazz. This was my first ever installation of UV glue TG. TG usually hold their oleophobic coating far far greater then your typical plastic film SP.
I did messed up my installation a bit. Here are my personal recommendation if you're going to install a full UV glue TG.

1. Taping the upper speaker grill will help you align your TG greatly. You'll noticed that the upper bezel is smaller than the lower bezel. If you tape your upper speaker grill just enough to cover the grill, you'll end up with a near perfect TG alignment. 3 tapes were provided with the TG.

2. When you drip the UV glue, dont squeeze the tube too hard. You'll get bubbles in the glue blob. You can get rid of the bubbles using the dust tape. You'll probably need a flashlight to ensure no small bubbles reside in the UV glue blob. With the screen off, you cant see the mini bubbles. I got 3 miniscule bubbles on my installation. Not visible in dark background. Only with white background you'll notice the bubbles. Like right now when I'm typing this. Haih....

3. Make sure your hands are not contaminated with the wet UV glue during installation. It'll leave prints on your TG.

4. I used a powerbank to power the provided UV light. It'll turn off automatically around 1min or less. Not sure if its my powerbank or all powerbank behave like this. But its a good thing cause you can switch position each time it powered off.

5. Only wipe the spilled glue when the UV glue is almost or already dried. Dont wipe it when its still wet. Your cloth/tissue will absorb the glue from the edges if its still wet.

Those were my personal noob opinion when installing the full UV glue TG.

Case compatibility? 100% with all the cases that I have.
Added bulk/weight? I dont feel any difference. Quite possibly because the phone itself is substantial heavy, and adding the case as well.
TLTR - go get sakurazz's help if you're not confident.

Later report back. Changelogs didnt say much on this 

Best online shop to get OP7?

wanna check, the import version oneplus 7 pro can support malaysia LTE-A CA?

also, is it any usb-a to type-c cable can use for warp charging?

Mostly bought an AP unit rite? Or official Malaysia unit?

Btw, anyone know how to know which rom am in on? Either eu or global? And if I am on eu rom, can I flash the global rom just like tat?

Is there any problem if I install global on top of my eu rom?

Btw anyone having issue that the WhatsApp when wan attach photo will hang there.. WeChat also.. but accessing gallery have no problem.. need to restart to be able to attach photos again..

I'm planning to visit melawati mall this depaavali...

Any phone shop there selling this phone screen protector ??? At my place none of phone shop selling any product for this phone......

Also l want shop staff to help installing SP becoz l already failed at it before this.......

bro u went to kl just to install the TG?