Just bought Brisbane and Biostar TA690G

Sorry for my noobness, but why is it my multiplier becomes x5 instead of x9.5 Now running at stock @ 1.0GHz

im sure u enabled the CnQ feature
disable it, and ur clock will become normal (1.9GHz)

where's the feature? I didn't find it anywhere

the only thing I manage is HTL

im not sure if ur BIOS setting is same with my TForce 570U, but perhaps u can change it in the BIOS..go to Advanced Chipset Features and disable the CnQ feature

Thanks, will pound on that now. Is there any good solution for AMD processor with crossfire?
Now thinking to get the 2900XT.

How much is DFI and Abit? Cant seem to find any price on lowyat pricelist.

This post has been edited by DevilMan: Jun 17 2007, 04:02 PM

this is my clockspeed: 2415MHz


but i remember running the benchmark last time can get around 7000mb++ coz i running dual channel with around 62% efficiency of the bandwidth...
now only 52% eficiency...
sisoft got problem d?

Hello guys im a new here and i like to join this club


i hope soulfly can addme in

3600+ X2 Brisbane G1 | seram | BIOSTAR TForce 570U | Patriot PC2-PC5300 | Cooler Master Eclipse | 2699 MHz

DFI INFINITY CFX3200-M2/G

dont ask for availability ask im not a representative of any shops
no such motherboard in the pricelist..
only ATE that bring the TForce 590SLi..last time they brought Fatility as well..
about the crossfire mobo, try search at Trade Zone..im sure there is a bulk for DFI..

This post has been edited by kalakatu: Jun 17 2007, 07:32 PM

How bout me?

3600+ X2 Brisbane G1 | afosz | BIOSTAR TA690G-AM2 | Mushkin DDR2-667 | stock HSF | 2526 MHz



This post has been edited by afosz: Jun 17 2007, 09:59 PM

@afosz
Dude, use 32M to test stability. Not 2M


-pWs-

nice result for 1T timing..change it to 2T if u want to go further
plus Brisbane can be pushed more..do u use the Automatic OC Engine?

Sorry bro, will update again tomorrow

So by changing to 2T, I can push even more? Nope, I do it manually. Still learning though. Only know in HT, bus and RAM divider only. I didn't touch the volt and RAM timing part yet coz no knowledge about it

Yea...Kalakatu is right. It is hard to maintain oc in 1T command rate. Try 2T, u can achieve higher


-pWs-

Thanks a lot. I see 2T doubles cpu multiplier from SP2004. Once satisfied, I'll post 32M here

This post has been edited by afosz: Jun 18 2007, 01:24 AM

yes, by 2T u can push even more..
but if u feell wanna OC until the highest u can go for 1T command rate, just go for it..
(dont forget to upload the SuperPI 1M and 32M here)

well, the vdimm is just simple..
lowest vdimm for TForce is 1.95v if im not mistaken..
i assume ur ram is value, so i suggest the max vdimm u can apply for ur ram is 2.2v..
if wanna higher, better get urself a ram cooler..

and besides changing the command rate from 1T to 2T, u can also play with timing and divider..loose the timings and lower the divider to go further

This post has been edited by kalakatu: Jun 18 2007, 01:22 AM

I understand the divider, but didn't quite get the timing part. Now is 4.0-4-4-12, so I which do I need to change in order to go higher? After I crash, is it already my limitation, or I need to tweak here and there to make it stable and go further?

crash? perhaps not enuff voltage? but since u use Brisbane, maybe u need to pump just vdimm..
increase ur vdimm first, if still crash then lower the divider (DDR533 or DDR400) and loose the timing (i.e. 4-5-5-15 @ 5-5-5-15)

to smokey and seram too...

Can my RAM go any higher as it also shares for VGA

this mine... hehehehe...
i got it from allenultra...
thanx 4 good mobo n cpu..
actually i'm very noob about oc...
since he didn't downclock,
this is my oc cpu... hahahahaha..
but i wonder why my temp cpu reading was so low...
i have run that pc at 2.62 48 hours non stop...
my frenz said, if i oc cpu, the temp will be higher...
somebody plz give some opinion??