is brisbane available at lyp or must buy through bulk? whats the id on the box? AXD something2....

i dun think that is necessary 
reason - i dunno..
becoz normally i inly played with vcore and vdimm 

try to pump more vcore..
and since u still using stock cooler, better keep it under 1.5v..
and set the divider to the lowest (533 or 400) and loose the timing (CL5 perhaps?)

For Brisbane 3600, it is consider high voltage at vcore 1.45. Normally with 1.4vcore, u can oc around 2.9GHz already

---

Added on June 9, 2007, 2:56 pm

Try to use other multiplier
-pWs-

I keep my HT below 1000.
Setting HT multiplier @ 4x wont effect performance much.

Refer to the table on the 1st post. That's your answer-ram divider is selected by the CPU based on the CPU multiplier and DDR2 setting in CMOS.

i believe mfa333 tried...

300fsb x 9.5cpuMul = 2850

9.5 normally refer to 9cpuMul.. so 533divider should 7
me also face the same prob... but... the high transfer rate reading won't bother me much..
it's should 7 not 8...

other thing still i can't solve while doing 316fsb ~3ghz, which i ran it now..
cannot using 667divider... i manage to use below 270fsb only when using 667divider..

3000 / 6 = 500..

my ram can even run 520 if using 800 divider...

most of the time i tweak basic timing.. sub option i'll leave it auto..can save much time..
since tighter timing make more transfer rates.. so it won't interest me much to try higher with loose timing..
brisbane 3600+ cpuMul is 9.5.. we cannot increase it, only can change downward..
800Mhz ram won't cheap.. it's RM100 more than 667 DDR2 for 1gb..
if 2 for dual channel will cost RM200 more..

i know kingmax is cheaper... only recently.. but other brand price not drop yet..

Didn't notice until you mentioned. But anyway, here's the formula to calculate

Ram speed = multiplier * 200 / lowest number that does not overclock ram * 2

The memory controller will only accept the following speeds DDR400, DDR533, DDR667 and DDR800. The lowest divider (meaning highest ram speed) is 5.

Therefore if you set DDR800,
9.5 * 200 / 5 * 2= DDR760 -ram can't be set any higher because no higher divider than 5. Ram is not overclocked, so this will be used

For DDR667
9.5 * 200 / 5 * 2= DDR760 -CPU thinks ram is overclocked, so it will used a lower multiplier
9.5 * 200 / 6 * 2= DDR633 -CPU thinks ram is not overclocked, so this will be used

For DDR533
9.5 * 200 / 7 * 2= DDR543 -CPU thinks ram is overclocked, so it will used a lower multiplier
9.5 * 200 / 8 * 2= DDR475 -CPU thinks ram is not overclocked, so this will be used

The memory controller will choose the divider based the ram speed setting and CPU multiplier with the aim of having a ram speed as close as possible to the ram speed setting while not overclocking the ram while assuming base clock is 200. The base clock does not affect the choice of ram divider, which is why overclocking ram is possible even for DDR800 which does not have a higher speed setting to use.

---

Added on June 12, 2007, 9:53 pm

Most likely, because on /7 it will be faster than 533 while on 200HTT, and the processor won't allow that.

flashed to 507 liao...
now managed to boot at 260mhz @ stock voltage @ without CnQ @ virtualization enabled (wats tat?)...but havent prime yet...
but i dunno y cant even boot at 270mhz @ 1.4v @ ddr400 @ without CnQ @ virtualization enabled (wats tat?)...
y ar?

stock is 1.3v ma
i alrdy put 1.4v wor...

@afosz
Dude, use 32M to test stability. Not 2M
-pWs-

spoilt???u mean??

---

Added on June 18, 2007, 2:30 amwhat is dTS?????????????

---

Added on June 18, 2007, 2:30 amwhat is dTS?????????????

why not try 316fsb.. loose all the trfc if cannot boot..

what speed that ur brisbane can hit?

Apa mobo AM2 yang best bawah RM300?