Did you buy the 003 model, Strike ZAFT fighter ? It seems the earlier models have lots of problems, since TT still new then.

The later models are better. I've seen the completed Strike FBM, its much better (as in fewer parts with problem). However, for all models - the colour still not quite right, especially yellow (too dull) and red (too glossy).

That's why when assembling TT, super glue is a must have

yeap. 003 model.

din notice when i buy. but when i go back and see, i anticipated problem liao cos early versions...

anybody know shop selling TT HongLi near Kajang??

Bro..the nearest is at Cheras Leisure Mall..at least thats where i know selling...there is another shop i saw last time..at Cheras batu 9..behind AYAM Mas...haha

I know the shop in Leisure Mall, there was 2 shops selling there. one of them sell more $$.

I will like to know how was the price in Cheras Batu 9 you last seen?

Buying pirated goods = bad stuff

But seriously, the earlier kits from TT are just plain bad.

unless i wan another fodder, i'll skip TT Hong Li liao

Nice review on TT version Parody. The booklet you mentioned is just like BD one. The BD version also has the used runners for certain constructed parts.

I just checked it on Dalong.net and you're right. Thanks for pointing it out.

I didn't know because all other BD MG kits don't have this feature. Even the latest Musha Mk II.

When last time..the price was cheaper compared to the ones in Leisure Mall..maybe bcoz of the lower overheads..haha

Please read carefully about the previous post. We are talking about shinnaju. The only two MG I didnt buy are SF and Hi Nu 93v2. I also didnt buy any TT PG beccause with that kind of money I prefer Bandai Nz666.

Few tips for @1. loosen parts = apply 1 layer of super glue and let it 100% dry, if it is still LONGAR apply second time.

@2. Got gap in between = either the internal part too thick or the rubber didnt go 100% inside the hole. You need to use your cutter and sand paper to solve the problem (this normally happened in A or AA stock "2nd batch")

@3. How to define A, AA, AAA and AAAA stock?(china never have B grade) Need to ask your seller, if he is honest you will get the answer. Normally the pricing will tell the truth, 1st batch always expensive than 2nd batch. Example Shinanju before CNY RMB130 now only RMB105 or less. TT hongli dont give a shit about quality, they just using the 1st batch molding for 2nd batch re-production.

@1 yeap i doing it already

@2 that one i also did as takumikun did liao. unvirginise the female connector. Only thing now i can't do much is the 'high-low' in the armor joints. :| i'll take pic when free.

@3 so meaning, which is better?

my HG 1/144 colector from kit TT n long








cheapers n good for eye looking...

*sory taken by hp camera#

MyKy44, China grading vs Malaysia grading : A=D, AA=C, AAA=B, AAAA= A (ini baru A). Next time check the quality before buy, especially the face(head) part. If you see the head part is blur, it is either AA or A grade.


Citoi : your Soma Peries wont feel lonely next week, his boyfriend hallelujah(Arios 1/144) on the way to malaysia.

This post has been edited by seikofarlim: Jun 24 2010, 02:09 AM

May i knw where got the shop selling such model?
ku nak seed series

hi hygoonia,

u can check wit takumikun... nice and friendly seller..

http://forum.lowyat.net/index.php?act=ST&f...0#entry33638215

How good is a TT hongli PG Mk2? can the parts snap perfectly?

TThongli ftw..........

Thanks for the heads up, mate.

QUOTE(jstbid @ Jun 25 2010, 09:49 AM)

How good is a TT hongli PG Mk2?  can the parts snap perfectly?

Not all parts though.

should be careful of china gundam. Their materials might not conform to safety standards. hence when you sand it, might be dangerous to breath in those debris.