Welcome Guest ( Log In | Register )

Bump Topic Add Reply RSS Feed

Outline · [ Standard ] · Linear+

 Xiaomi Router 3, Flash Padavan - unifi

views
     
iRonTech
post Apr 18 2017, 11:43 AM

Access Denied
*******
Senior Member
8,621 posts

Joined: Nov 2004
what mtu size u guys put in? 1492 seem doesn't work after ping www.tp-link.com -f -l 1492 test, max only 1440. btw, i'm using maxi$ 30Mbps.
iRonTech
post Aug 14 2017, 08:34 AM

Access Denied
*******
Senior Member
8,621 posts

Joined: Nov 2004
QUOTE(skydrake @ Aug 12 2017, 10:05 PM)
ok ok thanks for helping!

[attachmentid=9040191]

[attachmentid=9040193]
*
change your mi router IP to 192.168.1.254 will do. (1.1 crash with the ONT)

This post has been edited by iRonTech: Aug 14 2017, 08:38 AM
iRonTech
post Aug 14 2017, 10:17 AM

Access Denied
*******
Senior Member
8,621 posts

Joined: Nov 2004
QUOTE(skydrake @ Aug 14 2017, 09:57 AM)
I tried change to 254, same also. is it possible that my pppoe pwd is not +1 behind? thx for helping
*
follow step 7

ONT port 2 link to mi router wan port?
iRonTech
post Aug 14 2017, 07:05 PM

Access Denied
*******
Senior Member
8,621 posts

Joined: Nov 2004
QUOTE(skydrake @ Aug 14 2017, 01:56 PM)
I had followed steps 7 on page 1.

my ONT is hg8240h, I tried accessing into it and the configuration is totally different from page 1 tutorials. I not able to find any settings regarding the lan 1 or 2.

I tried to check is those lan ports required settings or not by changing the maxis router from ONT default port 1 to 4 one by one and it still able to dial for internet access. So I try removing maxis out and put in mi router into ONT from port 1 to 4 one by one still not able to access.

possible needs to find data sheets to configure the ONT first?
*
don't need, unless u need both thomson & mi3 work together

try disable PPPoE & MAN Access, then the iptv see if PPP wan connected

my wan config sample,



Attached Image Attached Image

This post has been edited by iRonTech: Aug 14 2017, 07:18 PM
iRonTech
post Aug 14 2017, 10:26 PM

Access Denied
*******
Senior Member
8,621 posts

Joined: Nov 2004
QUOTE(skydrake @ Aug 14 2017, 08:39 PM)
[attachmentid=9044361]

[attachmentid=9044362]

Thanks for helping iRontech, I beginning to suspect is not the setting problem coz the setting is is straight forward mah, I followed everything as u told n it should work u r using it. might be few items below;

1. my pppoe password is not like what Maxis default mentioned like below
12345@home.maxis.com.my
123451 *+1 behind will be the password as mentioned*

2. possible the firmware I use got problem? But I got the 5aa2a75 from here > https://forum.lowyat.net/index.php?showtopi...&#entry83615598

3. possible my Mi3 WAN port faulty?

almost wants to give up  rclxub.gif , I bought this router from lazada RM95 only *after coupon discount la. LOL
*
The additional 1 behind your username id as the password is correct. What do u mean yours different (or call maxis cs to verify)?

here the log & status if id / password problem (changed mine to 1234567. And after insert correct password I need reconnect twice then only get connected)

Attached Image Attached Image



here wan port status for your question 3

Attached Image


can try cf494ea here

This post has been edited by iRonTech: Jul 18 2018, 10:26 AM
iRonTech
post Aug 15 2017, 06:43 AM

Access Denied
*******
Senior Member
8,621 posts

Joined: Nov 2004
QUOTE(skydrake @ Aug 14 2017, 11:30 PM)
I tried to see the log and find out my router is having difficulties to connect with the ONT I assume from what I have on the log. it has not even been thru the pppoe authentication like the log u posted..

[attachmentid=9044651]

i still trying to get results from google on the log search...
*
have you tried swap another cat5 cable?

here the full log from power up
» Click to show Spoiler - click again to hide... «


May 25 17:11:10 pppd[432]: Plugin rp-pppoe.so loaded.
May 25 17:11:10 pppd[432]: RP-PPPoE plugin version 3.12 compiled against pppd 2.4.7
May 25 17:11:10 pppd[433]: pppd 2.4.7 started by admin, uid 0
May 25 17:11:11 miniupnpd[441]: version 2.0 starting UPnP-IGD ext if ppp0 BOOTID=1495703471
May 25 17:11:11 miniupnpd[441]: HTTP listening on port 21137
May 25 17:11:11 httpd[435]: Server listening port 80 (HTTP).
May 25 17:11:11 kernel: br0: port 3(rai0) entered forwarding state
May 25 17:11:11 kernel: br0: port 2(ra0) entered forwarding state
May 25 17:11:11 kernel: br0: port 1(eth2.1) entered forwarding state
May 25 17:11:27 kernel: mtk_esw: Link Status Changed - Port WAN Link Down
May 25 17:11:27 detect_link: WAN port link down detected!
May 25 17:11:30 kernel: mtk_esw: Link Status Changed - Port WAN Link Up
May 25 17:11:31 detect_link: WAN port link restored!
May 25 17:11:36 kernel: mtk_esw: Link Status Changed - Port WAN Link Down
May 25 17:11:37 detect_link: WAN port link down detected!
May 25 17:11:38 kernel: mtk_esw: Link Status Changed - Port WAN Link Up
May 25 17:11:39 detect_link: WAN port link restored!
May 25 17:11:45 pppd[433]: Timeout waiting for PADO packets
May 25 17:11:50 pppd[433]: PPP session is 32256 (0x7e00)
May 25 17:11:50 pppd[433]: Connected to 00:00:5e:00:01:07 via interface eth2.621
May 25 17:11:50 pppd[433]: Using interface ppp0
May 25 17:11:50 pppd[433]: Connect: ppp0 <--> eth2.621
May 25 17:11:53 pppd[433]: Remote message: Authentication success,Welcome!
May 25 17:11:53 pppd[433]: PAP authentication succeeded
May 25 17:11:53 pppd[433]: peer from calling number 00:00:5E:00:01:07 authorized
May 25 17:11:53 pppd[433]: local IP address 10.x.x.x
May 25 17:11:53 pppd[433]: remote IP address 10.x.x.x
May 25 17:11:53 MI-3: WAN up (ppp0)
May 25 17:11:53 PPPoE: Connected
May 25 17:12:01 NTP Client: Synchronizing time to pool.ntp.org.
Aug 15 04:54:10 NTP Client: System time changed, offset: 7040528.286590s
Aug 15 04:54:21 pppd[433]: System time change detected.


This post has been edited by iRonTech: Aug 15 2017, 06:51 AM
iRonTech
post Aug 15 2017, 07:53 AM

Access Denied
*******
Senior Member
8,621 posts

Joined: Nov 2004
QUOTE(skydrake @ Aug 15 2017, 06:55 AM)
I will try to swap the cable later, maybe I should swap the one maxis  is using instead. hopefully this should be the issue. tjx again!
*
try factory reset the mi3 as well, ip as 192.168.1.254 & make sure the WAN (Advanced WAN option) is router instead of AP
iRonTech
post Aug 16 2017, 11:17 AM

Access Denied
*******
Senior Member
8,621 posts

Joined: Nov 2004
QUOTE(skydrake @ Aug 16 2017, 02:09 AM)
I had tried swaping the lan cable from the maxis to mi3 and is not working. lastly, I make my best bet will be the firmware or settings. the logs I have looks a bit abnormal comparing yours. don't have time to test yet for below;

1. reset
2. redo the padavan process maybe?
3. I can't find the setting u mention "make sure the WAN (Advanced WAN option) is router instead of AP", can SS? sorry for trouble.
*
try reset.


the huawei ONT, have u tried change to LAN port 2 & link to mi3 WAN port?

This post has been edited by iRonTech: Aug 16 2017, 12:02 PM
iRonTech
post Aug 18 2017, 09:51 AM

Access Denied
*******
Senior Member
8,621 posts

Joined: Nov 2004
QUOTE(skydrake @ Aug 18 2017, 02:09 AM)
I reset twice, still "timeout waiting for PADO packets" a more then 5-6 times .. I give up waiting. tried port 1,2,3 & 4. Still same. I try update promethues and follow the steps rebuild tool chain and flash firmware again. still waiting for tool chain building now.. later try again, if same "timeout waiting for PADO packets"... i guess maybe my router problem? or that hg8240h ONT needs setting to recognize 3rd party router.. headaacheee  cry.gif
*
probably Special Requirement from ISP MAC Address section insert the thomson mac address? hmm.gif
iRonTech
post Jul 18 2018, 10:26 AM

Access Denied
*******
Senior Member
8,621 posts

Joined: Nov 2004
e6f4533 available, use at your own risk

Attached Image



anyone tried mi router 3g?Attached Image

This post has been edited by iRonTech: Jul 18 2018, 12:02 PM
iRonTech
post Jul 18 2018, 11:26 AM

Access Denied
*******
Senior Member
8,621 posts

Joined: Nov 2004
QUOTE(chiafoo @ Jul 18 2018, 10:49 AM)
How do u change the language to English? I think thy remove change language option in latest prometheus . I dled latest prometheus but cant find option to change language which previously available with Shift+L
*
I'm onVMWARE-PROMETHEUS-64-UBUNTU-EN-RU.7z , din't change any lang but update script & source. 371MB should be eng ver

https://yadi.sk/d/6EpD2EpHmB82o


just checked, on the main menu press S, 4, 4 switch to en

This post has been edited by iRonTech: Jul 18 2018, 12:00 PM
« Next Oldest · Networks and Broadband · Next Newest »
 

Add ReplyOptions
 

Change to:
| Lo-Fi Version
 0.0292sec    0.83    7 queries    GZIP Disabled
Time is now: 28th November 2025 - 02:17 PM
All Rights Reserved © 2002- 2025 Vijandren Ramadass (~unite against racism~)
Removal Request
Powered by Invision Power Board © 2025  IPS, Inc.