Welcome Guest ( Log In | Register )

Outline · [ Standard ] · Linear+

 Coffee Lover v.2 Thread, Let's Share!

views
     
Keng
post Oct 30 2019, 11:52 AM

Getting Started
**
Junior Member
142 posts

Joined: Sep 2004
QUOTE(tishaban @ Oct 30 2019, 04:35 AM)
I'm happy to give away a handful of the o-rings for free
I don't have any extras for the other parts
*
how can i get it from u?
Keng
post Nov 2 2019, 03:04 PM

Getting Started
**
Junior Member
142 posts

Joined: Sep 2004
QUOTE(Ryou @ Oct 31 2019, 11:49 AM)
Any Breville Dual Boilers out there managed to get a bottomless portafilter? The original one from Breville seems ridiculously expensive. I wonder any other third party bottomless portafilter fits it or not.
*
Wanted to buy the ori naked PF from Breville Oz last time at less than Rm300 but still couldn't convince myself to spend that kinda money sweat.gif
Keng
post Apr 19 2020, 09:16 PM

Getting Started
**
Junior Member
142 posts

Joined: Sep 2004
Guys,

Any idea if there's any Baratza service center in Malaysia? My Sette went dead yesterday morning in the middle of a grind. Checked both the fuse on the cable and the power supply board already.

I've emailed Pulp since they are a distributor. Any help will be appreciated. Now using my backup hario manual grinder sigh.
Keng
post Apr 20 2020, 08:25 AM

Getting Started
**
Junior Member
142 posts

Joined: Sep 2004
QUOTE(ymeng85 @ Apr 20 2020, 02:03 AM)
You're based in KL?
*
Yes meng
Keng
post Apr 20 2020, 11:24 AM

Getting Started
**
Junior Member
142 posts

Joined: Sep 2004
QUOTE(Johnslow @ Apr 20 2020, 08:41 AM)
PULP or now called PPP Coffee is the official distributor in Malaysia

I got the Burr holder for my encore from them 5 years ago.

Try email techmy@pppcoffee.com . I tried 4 days ago, i want to buy more burr holder but no reply.

I think MCO not working

Good luck .  cool2.gif
*
Thanks. I've sent an email to the address provided in their website but that was to their marketing team.

Ran a bit more test just now, power supply board failure. Interface module is working fine.

user posted image
Keng
post Apr 23 2020, 01:30 PM

Getting Started
**
Junior Member
142 posts

Joined: Sep 2004
QUOTE(pierreye @ Apr 19 2020, 07:46 PM)
CRM3605 is using PID stock. No mod needed on the temperature sensor unlike some other machine which is using analog thermostat. You just need to pre heat the water tank to around 50 degree celcius so that the thermoblock have more headroom to stabilize the temperature during brewing. Another advantage is more powerful steam when steaming milk.

The only mod you need to do is the pump. If you unscrew the bottom, you will see the connection for the pump. You just need to unplug the wire from the circuit board to the pump, tap the pump to the 500w dimmer switch or solid state regulator. I'm using solid state regulator with 100k ohm potentiometer. When brewing, turn the knob almost to the minimum. As I'm using bottomless portafilter, the pre-infusion take around 10 seconds and will saturate the puck. Turn the knob to increase the flow while watching the pressure gauge. Once it reach 9 bar, stop there and continue to extract. You can play around with the pressure during brewing process. One of my favourite method is to slowly ramp down the pressure to around 6 bar before reaching my desire extraction weight.

PS: Ignore the red switch. Previously use the red switch to manually switch on the heater for old Poemia espresso machine. Not use in Gemilai. The potentiometer come with the solid state regulator resistance is too high and at minimum will stall the pump.
https://www.ebay.com/itm/1pc-KYOTTO-AC-Soli...oUAAOxyqUpQ9Lgb
https://www.ebay.com/itm/B100K-Ohm-3-Termin...bsAAOSwzaJX90kz

user posted image
user posted image
*
Just noticed this post. Nice DIY! Can see the potential of automate the pump power by reading the pressure.


5 Pages « < 3 4 5Top
 

Change to:
| Lo-Fi Version
0.2408sec    0.23    7 queries    GZIP Disabled
Time is now: 7th December 2025 - 05:52 AM