Have u check on Ultra 120?

Did it fit?

ultra 120 dont support soc 478

What about Ultra 90?

ultra 120 & 90 do support 478
just that u need to buy the adapter

This post has been edited by E-J@1: Dec 3 2006, 09:34 PM

I've heard about this before, but i can't seem to find the adapter for socket 478 for those Thermalright Ultra Series...

ya la, where to get? also where to get ultra-90, hardly see anybody in this forum using it

It's not like it's hard to get Ultra 90, it's becuase people tend more to get that Ultra 120 more than the Ultra 90...

hmmmm.... good suggestion, guys.. thx...

i think i will order from http://www.sidewindercomputers.com or from those australia website.. just email sidewindercomputers

This post has been edited by irangan: Dec 4 2006, 01:37 AM

now everybody wants u to buy for them
better do a bulk then

hmmm.... seem that it is cheaper to buy through online than looking around like mad for ultra90 in malaysia..

i think i going to place the order for a Ultra 90 and 478 retention bracket. all that only cost me below 200 below postage and can reach in like 4 days. sometime i just love internet.

edited: guys, after a hint from sHawTY, i research on thermalright products and found that HR 01 fit my mobo too.. so the choice now is Ultra 90 ($22.95) or HR 01 ($31.95). both of it also need 478 retention bracket. planned to place order by tonight. hehe... thx in advance, guys

This post has been edited by irangan: Dec 4 2006, 11:58 AM

better make sure fan clips are included in the item for hr-01

sure... i just sent them an email about that.

guys, please give me some feedback. HR 01 or Ultra 90. cant find any review that compare both of it.

I think HR-01 should work a little bit better than the Ultra 90, it have more heatpipes...

Not quite sure about that, it's just my assumptions by the way...

thx for the info. HR 01 for me then

DAMM... Doom just pointed out one very important fact. HR 01 and Ultra 90 will place horizontal and not vertical like those socket 775. this means that it going to hit my DPS card. sigh....

Now that you've mention it, i've nearly forgot that u're using socket 478

Hmm, what are the other choices do you have in mind TS?

3D Rocket II from Gigabyte or Big Typhoon from TT.... getting confirmation from Gigabyte about my mobo.. if they can confirm that for me, i going to give them a good complain since mobo is a gigabyte.

i am getting piss off now... if really cant find any air cooling, i think WC is the way to go

WC?

What model?
Gigabyte oso kaa?

Those Gigabyte watercooling setup are quite nice, but if you have the money to go for gigabyte watercooling setup, might as well buy metalzone's budget watercooling setup, it's better than the gigabyte WC set, and i think it's cheaper by RM50 - RM100

Gigabyte Watercooling Set is RM550 right?
Correct me if i'm wrong...

This post has been edited by sHawTY: Dec 5 2006, 04:33 AM

yep, around RM550


if u going for WC, why don't u go for a new mobo + Thermalright HR-01/Ultra-90
same cost if u go for Giga WC la (RM500)... Thermalright = RM200 (RM300 left for mobo)

The problem is, it's hard to find a decent socket 478 motherboard...

TS is using one of the most unique and high end motherboard for socket 478...
It's unique, b'coz of it's 6 slot for DDR rams...

The only motherboard that can beat that motherboard performance would be either ASUS P4C800 E Deluxe or an ABIT IC7 MAX3...

But those two motherboard are really rare nowadays...