Yeah, I already got 2 drippers, 3 tanks and 2 mods. Lots of juices and DIY ingredients now.

Anyone experienced Ekowool? Been itching to buy and try it from lelong.

http://list.lelong.com.my/Auc/List/List.as...UBound=&x=0&y=0

Oh cool, Will give it a shot. Thanks

Still looking for more Crius review. If compare TFV4 with Bellus, TFV4 will blow it away. Significantly bigger RBA. Dual coil RBA is sold separately though.

Nice. Quite near to Genting Court. I'll drop by next week after my pay check on 22nd. New US juices price is going to be hard to swallow though.

Do you have Halo Belgian Cocoa, SQN "Insert flavor" Cheesecake and Glas Milk? 0mg is fine with me as well.
I trust international experts than local. Black or white, no grey.
SS heats up fast. Fire lower. Thicker cotton also helps. I wick 6mm of cotton thickness on 3mm coil.

This post has been edited by TristanX: Nov 14 2015, 10:11 AM

Get Lost?
http://www.imdb.com/title/tt0411008/

I will

Hehe ok.

One part Bowden's Mate plus the rest of Black Flag Fallen is delicious.

Try Smok TFV4 or TFV4 mini. RM120 for either one.

Your tank is subtank mini right? Just push the wick from the inside to the outside of the RBA hole (assuming you are using the latest RBA). Cut it outside the RBA. Make it fluffy so that the wick doesn't go back inside. The wick cut should be 6mm in width if your coil is 3mm.

Running quad kanthal 28g 6 wraps 3mm

RM5 from this

http://www.lelong.com.my/onovaportrends-dn...7-01-Sale-I.htm

Kanthal 4mm 24g 6 wraps! Bigger than yours

Oops, just wanna show that it can fit 4mm.

Yeah, the air flow is unrestricted. Full flavor. Maybe I should try dual coil vertical with 4mm this time. It gets the tank hot though.

Or this? Dual 4mm SS 316L 5 wraps. Probably 0.25 ohm



This post has been edited by TristanX: Nov 15 2015, 11:59 PM

Yeah, I'll slot in left side of the screw for top coil, right side of the screw for the bottom coil. I've done 3mm dual coil on this RBA. The wicking part is a pain in the ass. Gotta cut two thinner cotton and slot into the left and right side of the gap before doing the main wicking.

Here you go.





This post has been edited by TristanX: Nov 16 2015, 12:17 AM

I'll post a pic from the top side. Gonna do it again soon.

Yup but you gotta put some thin cotton through the left and right side of the coil first. Use a flat screwdriver or thin tweezer to push the cotton through. You can stuff a pole or screwdriver at the air flow hole to make sure there is no cotton wandering at the air flow area.



This post has been edited by TristanX: Nov 16 2015, 12:42 AM

You need to block the juice channel. Just push the cotton from the inside on the juice channel till you see it fluffy outside the RBA.

After completing the first level of wick directly on the coil, push the cotton inside and close it. Insert a rod or screwdriver that is around the same diameter with the coil then stuff the RBA with cotton till its full. I already showed the first level a post above you.

Dual coil SS 316L 26g 4mm 5 wraps.



Another example

https://www.youtube.com/watch?v=eGb19mfjA00

This post has been edited by TristanX: Nov 16 2015, 10:18 AM

Nope. Left side of the screw, not post. You can't have 2 legs from the same coil on the same post. You need positive and negative polarity to get the coil running. The screw has two sides for you to slot the coil legs in. I did top coil on left, bottom coil on the right side of the screw.

There is an example from post #2182 on the spoiler.

This post has been edited by TristanX: Nov 16 2015, 02:32 PM

Just screw enough to stop the coil leg from coming out. Adjust the coil before you tighten the screws.

The subtank mini vertical video is similar.

Welcome to the club. That's some expensive taste