That tank is borderline dripper level as far as performance goes. That much vapor/hit, I'd say cut your nic by half if you're planning for a 5 min vape break.
I usually drip at 1.5 mg and 3 on my tank. Even the Uwell Crown overwhelms me at my usual nic level.

Something are just too good to be true. But if you can wait it out, then wait. Even if I do became rich rich someday, saving a few bucks off doesn't hurt.

I guess they're going for something more...uhm.. "original" design. Maybe?

Voodovape? The unnatural green juice that have shit load of food colouring in them even when it's scientifically proven to cause harm when inhaled?
No wonder

ahha.. really.. lulz..

Smok TFV4 using TF-R2 dual coil RBA

Nichrome heats up and cools down faster. It has lower resistance comparing to kanthal. 0.39 ohm with Nichrome 6 wraps dual coil not compressed.

3mm

This post has been edited by TristanX: Oct 8 2015, 01:06 AM

Guys. Any experience about Thailand juice? Fren promise to get few bottle for me. If the taste ok plan to bring in

Vail can hook you up with one. Slightly used though. COD can.

whats the price?

Hmm imo, breakfast club's vape flake tastes better. But im not a cereal kind of guy. I'd go broke for yogurt-ish liquid tho.

I've found a juice close to Five Pawns Gambit!



Gambit "Lights"

Dunno. Dun really care about the price. Quality come 1st. Sure once I got, Puchong n sri petaling gang will b d tester

more details pls.. price, mg, local/imported?

hello sifus..i wanna ask something..bought velocity rda today...
i want to use 2 coils..4wrap kanthal 1.8mm 0.3ohm single + subox mini mod

however, it wont work..why??? single coil working perfectly,..

ohm too low

subox cannot support below 0.3??

and for calculation, i set to dual coil serial right ??
http://www.steam-engine.org/coil.asp?s=ds&...8&awg=24&id=2.4

nope, minimum is 0.3, even your total ohm is 0.29, it wont fire.

for steam-engine, just find setting you like and choose single coil, then manually divide 2 (if dual coil) in your head

example if you target for 0.4ohm and dual coil, set target resistance as 0.8ohm first.. then proceed to make 2 coil based on steam-engine suggestion

ajak plz... hehehe....

Hi, nak tanya.. Mana nak cari US e liquid(Ori) murah2...ade yg jual?

24awg again. Why are all you guys using 24? You're all using regulated mods, not mechs. You don't need to super subohm, you can just increase the wattage on your mod.

ok few questions
whenever i left my vape for quiet a while, say half a day, and i pick it back up, the 1st few vape will be very unpleasant, but it will get better and smooth after 4 to 5 puffs, is this normal or am i doing something wrong here?
and how do i prevent flavor spiting into my mouth?
thanks ahead for ur assistance
my setup now
kanger subtank, nichrome 26 4 wraps, 0.36 ohm
ipv3li - joule mode, 17J, 260 deg C

What u meant by that bro?

In a mech mod, the only way to draw more power from the battery/increase power was to go to lower ohms. Fatter wires like 24awg and reduced wraps on the coil is used to lower the ohms.
With regulated mods all you'd have to do to increase power is to up the wattage. You can use thinner wires like 26 or 28awg at a higher ohm with more wraps. You'd get better battery life and probably less juice used.